Clothes Smell After Washing In Front Loader

After initialing reporting on an unpleasant smell, I now find that washing the pouches does work to get rid of both the smell and any possible film that the pouch may have deposited on my filters. At this point both my Kinesis pouches are clean, do not smell, and are working just fine. I do recommend cleaning them thoroughly though before use. But they really are an elegant, simple design that just works. I use the smaller 4 x 4 one to hold my 112 Kase magnetic filters for my Nikon Z system. It attaches easily to my tripod and holds all my filters.

Strong material for holding all types of clothes, mesh material deters mildew smell when returning from travel, & stores discreetly.

Bought this to fit inside my check in bag, keep my gym shoes in this and the smell from them doesn't affect the rest of my clothes that are in compression cubes at all

Received today, I wont get to deep in the unboxing as its very easy and the paperwork is child proof. It all fit together and even shows you where on the cartridge to put your finger pressure when replacing the ink for best results. A few things to think about. First I used ultra smooth fine art paper from Epson, it will feed through the top loader sometimes, though much more consistent in the front loader. BUT...It must be Very straight, use the lines on the entrance tabs and make sure the are lined up Perfectly on each side or you will repeat until its perfect, and this is done by hand, the feeder will not straighten it for you if you start it even a little bit off line. I was able to print out all the pictures you see on the rack (13 )with the starter inks, I ran out of light grey first then light vivid magenta. I got 4 prints after the light black low prompt came on the little screen on the printer, the computer will tell you well before that. A bit to much play in some of the plastic covers, and the feed tray cover on the front feed Must be closed each time after you feed it before you print. It will load but will not print until closed but there is a prompt to do so. Maintenance box is about 15 percent full after all these prints and setup, so with an extra box included you have plenty of time, most came form initial setup of inks. I actually think its faster than the average review says, but I have never been a production printer and I usually do not print border-less, I mat my most of work and its just covering up Very expensive inks. The little screen is very well thought out, bright, clear and menu items easy to find, its a touch screen that swivels up but Its tight enough and does not move when you use it. I will edit this if I find anything that may be of use. I am glad to have it,.... and as ALWAYS.... very pleased with the way B&H provides the best shopping experience available online or in store....

I like the size of this insert. It fits nicely into all my front loader backpacks, so I'm not limited to a "photo backpack ". Also it is just right for my z7, 15-30, 24-70 and 70-200 all f/4. Plus batteries and a few filters.

I purchased the Back Loader but I did not like zipping it up and flipping it over to access the front panel. The Font Loader works. For Travel with 2 camera bodies, lenses, drone, mics and accessories the Pro Light Front Loader is great.

Since COVID we are streaming to YouTube but the camera was very near the ceiling and always had the ceiling lights in view and washing out the front of the room. By adding the extender we got rid of looking at ceiling lights and the washout.

Thought i lost this little torch, 9 months later it falls out off my washing machine, got stuck behind the front rubber door Gasket, still has the original battery that came with and it turned right on, A little rust near the ring that's all the damage it suffered. I'm a fire inspector and use this a lot to read gauges and find hidden no no's in back rooms, this light rocks don't hesitate just get one!

I found a bulk loader full of Ansco Super-Hypan, last made in 1967. After many development attempts and step-by-step improvements, I'm able to get usable, scannable, and darkroom printable (yes, really!) negatives. I'm use HC-110 at dilution B, and I add 45 drops (about 3mL) in my 400mL of developer. This works out to be 7.5mg/L of developer. Continuous agitation for 9 minutes is used to maximize activity in the highlights with the highly-restrained developer.

Just what I needed to use my top loader with my action x.