Convert Computer Speakers To Receiver Speaker Wire

Great for hooking up bi-wire floor speakers for the best high fidelity sound available from your receiver.

I bought these Sony Dolby Atoms speakers a few months ago and I more than happy, they look and sound great. The build quality is great the speaker box been wrapped with a flat black vinyl wrapped and looks amazing, on the back the speaker wire input are wire clips sorry no banana inputs, also I was very surprised how heavy these speakers are, trust me they have some weight to them. I believe the maximum watts are 100 and the Ohm's are 6. Just match these babies with the Sony tower speakers and you are good to go..

I used these speakers with JBL 19cs subwoofers for a weight room facility sound system. The total system consisted of 6 - 26c speakers and 4 - 19cs subwoofers. Wiring is made easy with the removable terminal blocks and passthrough wiring. Basically each speaker connects to each other in a line. This installation method reduces cost for speaker wire and labor involved with running extra wire. The terminal blocks have 4 wire holes. For the first speaker in the line will use holes 2 & 3 for the line connecting to the amplifier. Then a wire is ran from speaker 1 to speaker 2. Holes 1 & 4 from speaker 1 connects to holes 2 & 3 on speaker 2. This continues for the entire line. Be sure to properly power these speakers. Both the 19cs and 26c need 140 watts of power. In our installation we used 2 amplifiers splitting the system into left and right sides of the room. Since each amp had 2 outputs of 500 watts for each channel. This provided some headroom for the speakers. On both amps output 1 was was the high and output 2 was the low. Output 1 had 3 26c speakers and output 2 had 2 19cs subwoofers. These amplifiers had a built in crossover feature that splits the signal into high and low frequences which is essential for installing a system like this. A xlr splitter was used to convert the output from the mixer (1 xlr) to inputs for both amps (2 xlr). A cutout template is provided for cutting ceiling tiles. Once tiles are put back in the ceiling the installation can be done without access into the ceiling. The speaker is designed to push up through the cutout in the ceiling tile and clamps down to the C bracket (included). Make sure to have someone assist with installing, these can be insalled with one person but can be difficult for one person to lift, attach wires, put into place, and screw down holders. Overall these speakers work as expected and would buy again. They install nicely and end product looks professional. Nothing less to be expected from JBL.

I placed this amp in my basement and ran speaker wire outside to a pair of Polk audio atrium 8 speakers. Sound is amazing and so convenient to stream music every time I walk outside. I did a lot of searching and finally settled on this combo. Loving it. Highly recommended!

Asthetically i am very happy with the wall brackets design I bought Acoustimas 10 Ser.V speakers and Bracket UB-20 Series-II. As per instruction while fixing we found that the Speaker wire is getting bend to 90 deg twice, the cutout/ Slot is made at wrong place. believe me it hurted me lot after paying so much for Bracket. i request Bose to provide us justification why is it so?and speakers wire will not break. believe me for 1 week i am just thinking to bend wire or not?hence i am not able to install upon bose confirmation only i will install. in the cost of Bose Bracket there are other companies which provide the Speakers also and after paying so much of Cost if we get the Improper Item then it is not good. Bose to intervene the Design for Slots location and avoid Speaker wires bending i am very very big fan of Bose but got upset and unhappy due to this hence i am writing

We are using this receiver as the base of a fairly simple whole house speaker configuration. With a speaker router, it handles eight speakers at cocktail party level perfectly. There are more than enough inputs. Bluetooth set up was a piece of cake. For the price, A+.

I went from a 5 speaker surround sound system to these speakers and they're much better. I love to getting rid of all my extra speakers wires and receiver and being able to Bluetooth to the speakers is great also.

This is a truly useful item for setting up powered speakers on the road. Usually I place the powered speakers close to an outlet in the corner of the stage and/or hall. This 6' length is perfect for such a setting. In addition I use Alto wireless receivers to cut down on XLR cables - this multiple outlet allows me to power the speaker, the wireless receiver and a DJ light all at the same time. What's really cool is - when the speaker, or light or receiver is on, an LED indicator light lets you know something is turned on. When everything is turned off, the LED light goes off too. So I know when I've forgotten to turn of the speaker at the end of the night. This outlet is built tough and can take the abuse of the road - I highly recommend them for powered speakers!

This receiver meets my needs. I was able to use my 18 year old B&W subwoofer using the receiver's A speaker outputs to the sub woofer and the subwoofer speaker outputs to my Boston acoustics satellite speakers (would have been slightly easier with a subwoofer out). that left the B speaker outputs for another pair of speakers on my back porch. The only other wish would be for a zone two output (pre amp out) that works with all line in equipment including Phono and not just #4. Sound is great, simple to set up and simple to use. I would buy it again.

This is the perfect ideal adapter for using active speakers in a wireless capacity. Specifically, I use the Sennheiser wireless systems to send the signal to the speakers remotely. This adapter is for the needed for the Sennheiser transmitter/receiver packs for providing constant power verses using batteries. I hide the transmitter/receiver packs on top of each speaker out of site from the public and being able to plug them in to the same cord as the active speaker.