Difference Between Top And Front Loader Washing Powder

Just what I needed to use my top loader with my action x.

- all fits just great - very confortable dividers - Top Loader makes accesibility easier

Received today, I wont get to deep in the unboxing as its very easy and the paperwork is child proof. It all fit together and even shows you where on the cartridge to put your finger pressure when replacing the ink for best results. A few things to think about. First I used ultra smooth fine art paper from Epson, it will feed through the top loader sometimes, though much more consistent in the front loader. BUT...It must be Very straight, use the lines on the entrance tabs and make sure the are lined up Perfectly on each side or you will repeat until its perfect, and this is done by hand, the feeder will not straighten it for you if you start it even a little bit off line. I was able to print out all the pictures you see on the rack (13 )with the starter inks, I ran out of light grey first then light vivid magenta. I got 4 prints after the light black low prompt came on the little screen on the printer, the computer will tell you well before that. A bit to much play in some of the plastic covers, and the feed tray cover on the front feed Must be closed each time after you feed it before you print. It will load but will not print until closed but there is a prompt to do so. Maintenance box is about 15 percent full after all these prints and setup, so with an extra box included you have plenty of time, most came form initial setup of inks. I actually think its faster than the average review says, but I have never been a production printer and I usually do not print border-less, I mat my most of work and its just covering up Very expensive inks. The little screen is very well thought out, bright, clear and menu items easy to find, its a touch screen that swivels up but Its tight enough and does not move when you use it. I will edit this if I find anything that may be of use. I am glad to have it,.... and as ALWAYS.... very pleased with the way B&H provides the best shopping experience available online or in store....

I like the size of this insert. It fits nicely into all my front loader backpacks, so I'm not limited to a "photo backpack ". Also it is just right for my z7, 15-30, 24-70 and 70-200 all f/4. Plus batteries and a few filters.

I purchased the Back Loader but I did not like zipping it up and flipping it over to access the front panel. The Font Loader works. For Travel with 2 camera bodies, lenses, drone, mics and accessories the Pro Light Front Loader is great.

We replaced two HomePod minis with these Gen 2 HomePods. The sound difference is amazing. The HomePods sound so much better and can go much loader. We use these with the TV and the minis were too quiet for the room we were in.

Since COVID we are streaming to YouTube but the camera was very near the ceiling and always had the ceiling lights in view and washing out the front of the room. By adding the extender we got rid of looking at ceiling lights and the washout.

Thought i lost this little torch, 9 months later it falls out off my washing machine, got stuck behind the front rubber door Gasket, still has the original battery that came with and it turned right on, A little rust near the ring that's all the damage it suffered. I'm a fire inspector and use this a lot to read gauges and find hidden no no's in back rooms, this light rocks don't hesitate just get one!

I’ve always used kodak fixer but wanted to try this because it’s a few dollars cheaper. I don’t know the technical difference between this and Kodak’s powder fixer but I enjoyed how I could mix this bottle up to just a specific and easily measurable ratio. After stirring this up I don’t think I ever want to go back to powder chemistry. I use this for both ilford and kodak films.

I have mounted the 1440 Pelican top loader case on my Ducati Multistrata for use as saddle bags. I wanted top loader rather than side loader that dumps all your stuff out when you open it. I removed all handles and the large extendable handle (very easy to do), adjusted some of the plastic ribs on the back where it bolts onto the motorcycle mounting system and its good to go. I had alumnium bags before and they leaked, bent easily (made them leak worse) and didn't hold enough. I've had other pelican bags and they literally seem to be indestructable. The service from B & H was very quick and the price was the best I found. I've used B & H years ago for cameras and had forgotten them over the years. I haven't any negative comments. It took me a while to align and drill the holes on the first bag but the second went quickly.