Electrical Cabinet Air Cooler

Blows air like all the others but looks cooler doing it!

Much Better to install then a Air cooler

This review is for the 50L cabinet. The shipping box is way above average, meaning the product is well protected. It won't stop a forklift tine, but will survive substantial mishandling with the triple wall box, reinforced corners, and interior foam spacers. The build of the cabinet is sturdy and well crafted. All seams and corners are well fitted. Testing the power consumption, about 6.2 watts when the TEM cooler is on (cooler cycles like a refrigerator). Operation of the cabinet is absolutely quite due to the TEM cooler design. The interior lights are a joke, but may be helpful if you're groping in the dark. A continuous light strip would be better. The sculpted foam for lenses is another joke unless you have lenses under 70mm in diameter. That was replaced with a thin sheet of foam like the two other foam sheets they provide. My 200-500mm Nikon zoom with tripod foot fits on the lower deck in the 50L cabinet if put in diagonally with room for a couple lenses and accessories. As for the dehumidifier operation, the ambient humidity has been in the low 30% range this month, so haven't been able to test this out. Need to wait until summer when humidity gets nasty.

Awesome performance but runs a bit hot. Nothing a good air cooler can't handle though!

This chip comes close to the performance of the X-version. Except with lower power and temperatures. An air cooler can handle this cpu, no problem.

Ever since top vents started coming into vogue, I've longed for a case like this to make an appearance, and it's everything I wanted. The key differentiator of this case compared to most other, modern cases is that it has no vents on the top. For air cooling, this is ideal because you want air to go through the CPU cooler and out the back, not go out the top and skip the cooler entirely or come in from the top and screw up the flow direction. There is a slope in front of the top-mounted PSU that forces the incoming air from the empty space at the top of the front fans down into the CPU cooler. Then the GPU area is fed by additional fans on the bottom to ensure there's plenty of fresh air. This amount of airflow allows you to run the fans at pretty low speeds, being almost silent at 60% in the front and 40% on the bottom, while not significantly reducing the cooling potential. There are mesh filters in front of both sets of fans, keeping the interior a lot cleaner than it would be without them. The panels pop off nicely with some sort of magnetic or tension mounting. Overall, the design of the toolless access and working inside this case feels like an improvement over the Meshify C case I had before. Of course, there is one compromise. If you want non-nvme drives, it only has room for a couple on the rear of the motherboard panel, and there's not much airflow in that area, so I'd hesitate to use a spinning platter hard drive. At this point, I only use nvme drives and a separate NAS for storing media, so that's no problem for me.

Coupled with a Noctua NH-D15 air cooler and everything at stock/default settings, I encode hour long videos using. The CPU was at usage 96% capacity, temp at 65C with the CPU fan at 575 rpm and all cores running at or above 4.2GHz. Haven't tried overclocking yet, but looks like plenty of room. Certainly is great performance straight out of the box

Very happy with the Elements External drive with it sitting on a laptop cooler blowing air up through the drive. Stays at 42 C in a 23 C room. I would not be happy with the drive temperature otherwise. Had to assign a drive letter in Windows 7 to the external drive to access the drive. No issues after that

A powerful gaming CPU that is extremely capable. However, if you're an SFF builder, be prepared for how warm this CPU runs. Nothing that can't be handled with a proper AIO cooler, but if your ITX case only supports air cooling (i.e. Fractal Terra), then selecting an appropriate air cooler and applying curve optimizer may be essential to bring down the standard operating temps to something you can tolerate. Also, I agree with Dongun's review comment about the increased boot times. Bottom line: Highly recommended CPU.

This cooler pushes a good volume of air. It is well built and is able to operate tilted up or in the flat position. Rear legs provide two tilt heights. The front stoppers are a little tall and stick up a little too far for relatively thin laptops and to get in the way. But my laptop stay put firmly when the cooler is tilted to the first position so it has not been a real issue. Very happy with this cooler.