Front Loader Washer Parts

Received today, I wont get to deep in the unboxing as its very easy and the paperwork is child proof. It all fit together and even shows you where on the cartridge to put your finger pressure when replacing the ink for best results. A few things to think about. First I used ultra smooth fine art paper from Epson, it will feed through the top loader sometimes, though much more consistent in the front loader. BUT...It must be Very straight, use the lines on the entrance tabs and make sure the are lined up Perfectly on each side or you will repeat until its perfect, and this is done by hand, the feeder will not straighten it for you if you start it even a little bit off line. I was able to print out all the pictures you see on the rack (13 )with the starter inks, I ran out of light grey first then light vivid magenta. I got 4 prints after the light black low prompt came on the little screen on the printer, the computer will tell you well before that. A bit to much play in some of the plastic covers, and the feed tray cover on the front feed Must be closed each time after you feed it before you print. It will load but will not print until closed but there is a prompt to do so. Maintenance box is about 15 percent full after all these prints and setup, so with an extra box included you have plenty of time, most came form initial setup of inks. I actually think its faster than the average review says, but I have never been a production printer and I usually do not print border-less, I mat my most of work and its just covering up Very expensive inks. The little screen is very well thought out, bright, clear and menu items easy to find, its a touch screen that swivels up but Its tight enough and does not move when you use it. I will edit this if I find anything that may be of use. I am glad to have it,.... and as ALWAYS.... very pleased with the way B&H provides the best shopping experience available online or in store....

One look at these parts and you realize that they are nicely made, high quality and well thought out. The manufacturer provides a nylon washer that fits inside the bottom of the female thread to cushion the fully engaged adapter. Pleasure to see this quality.

I like the size of this insert. It fits nicely into all my front loader backpacks, so I'm not limited to a "photo backpack ". Also it is just right for my z7, 15-30, 24-70 and 70-200 all f/4. Plus batteries and a few filters.

I purchased the Back Loader but I did not like zipping it up and flipping it over to access the front panel. The Font Loader works. For Travel with 2 camera bodies, lenses, drone, mics and accessories the Pro Light Front Loader is great.

Someone please tell me any other film washer better than this.

Just what I needed to use my top loader with my action x.

I did not encounter any issues with assembly. A stub screwdriver is included but you'll want to use your own nicer one because the parts of the rack come with numerous screws pre-screwed in which have to come out first. I screwed together all parts loosely first followed by tightening to help with hole alignment. I had also purchased a shelf and appropriate mounting hardware but the extra hardware was unnecessary because the baggies of 10-32 screws and 12-24 screws that were included with the rack were more than sufficient. Very minor notes: the Auray badge stuck to the front was also offset on my rack, and, the main B&H image of the rack shows the back plate below the front edge of the top which is a little funny because the manual indicates it's to be installed on the back--not that it matters.

I got this case recently and have had nothing but a great experience with this case. Beautiful RGB lighting on the front, great airflow with the mesh on the front. All of my parts go nicely with the case as well. I previously had an NZXT H510, although that looked nice as well, this TD500 not only looks nicer, but also as I mentioned has much greater airflow. If you are going to build a PC and cannot decide what case you want, trust me when I say that this case certainly is a great choice.

- all fits just great - very confortable dividers - Top Loader makes accesibility easier

great quality, durable, and zero's in very easily. Ready for muzzle loader season!