Front Loader Washer Repair Manual

Received today, I wont get to deep in the unboxing as its very easy and the paperwork is child proof. It all fit together and even shows you where on the cartridge to put your finger pressure when replacing the ink for best results. A few things to think about. First I used ultra smooth fine art paper from Epson, it will feed through the top loader sometimes, though much more consistent in the front loader. BUT...It must be Very straight, use the lines on the entrance tabs and make sure the are lined up Perfectly on each side or you will repeat until its perfect, and this is done by hand, the feeder will not straighten it for you if you start it even a little bit off line. I was able to print out all the pictures you see on the rack (13 )with the starter inks, I ran out of light grey first then light vivid magenta. I got 4 prints after the light black low prompt came on the little screen on the printer, the computer will tell you well before that. A bit to much play in some of the plastic covers, and the feed tray cover on the front feed Must be closed each time after you feed it before you print. It will load but will not print until closed but there is a prompt to do so. Maintenance box is about 15 percent full after all these prints and setup, so with an extra box included you have plenty of time, most came form initial setup of inks. I actually think its faster than the average review says, but I have never been a production printer and I usually do not print border-less, I mat my most of work and its just covering up Very expensive inks. The little screen is very well thought out, bright, clear and menu items easy to find, its a touch screen that swivels up but Its tight enough and does not move when you use it. I will edit this if I find anything that may be of use. I am glad to have it,.... and as ALWAYS.... very pleased with the way B&H provides the best shopping experience available online or in store....

I like the size of this insert. It fits nicely into all my front loader backpacks, so I'm not limited to a "photo backpack ". Also it is just right for my z7, 15-30, 24-70 and 70-200 all f/4. Plus batteries and a few filters.

I purchased the Back Loader but I did not like zipping it up and flipping it over to access the front panel. The Font Loader works. For Travel with 2 camera bodies, lenses, drone, mics and accessories the Pro Light Front Loader is great.

I had a manual Disc repair that worked OK but you could really see the swirls. My neighbor loaned us some store bought DVDs which had scratches because they have a kid also. I asked them if we could use this Repair tool on disney's Toy Story 3. It took out all the scratch marks except for one very deep scratch,. No swirls!! (Well you have to look under an incandescent light at just the right angle to see super fine swirls). This really does as advertised cleans up to 99% scratches. And it's already payed for itself after restoring only 2 discs. Of course we are restoring all our scratched DVDs. Well worth the money!

Someone please tell me any other film washer better than this.

Just what I needed to use my top loader with my action x.

Thanks!!! Easy to repair!

It works great! No wires running to a manual mixer. Set it up at the front of the stage and run wires across ice front of the stage. No wires across behind us or out to a mixer out in the audience. Nice eat easy set up. I did add an inexpensive router and used a Ethernet patch cable which I think helped. Great system!

I have an old Nikkor 400mm f3.5 manual focus lens that weighs about 6 pounds and is front heavy; it is not practical to hand-hold and shoot this lens because I cant use the normal technique that one uses with an autofocus telephoto lens, which is to support the lens with my left hand while using the autofocus button with my right hand. The lens is manual focus only and its just too heavy to both focus and support this lens with my left hand while holding it at the focus ring. The monopod comfortably supports the weight of the lens and frees up my left hand for focusing with the focusing ring. I also have a tripod, which is better for using this lens, but also heavy so I dont like to haul it around if I am doing much walking. The monopod serves much better for long hikes and is sturdy enough to bear the weight of my equipment. To simplify and expedite mounting, I have attached Swiss Arca compatible quick release receivers to both the tripod and monopod, and a Swiss Arca release plate on the lens. This allows me to remove and remount the lens quickly and easily. It also enables me to mount the lens in a fashion that somewhat compensates for its front heaviness. So I am very pleased with this setup.

I just bought this motherboard. When I face to the front panel control problem. The manual confused me. Hope asus can quickly fix it.