Front Loader Washer Stand

Received today, I wont get to deep in the unboxing as its very easy and the paperwork is child proof. It all fit together and even shows you where on the cartridge to put your finger pressure when replacing the ink for best results. A few things to think about. First I used ultra smooth fine art paper from Epson, it will feed through the top loader sometimes, though much more consistent in the front loader. BUT...It must be Very straight, use the lines on the entrance tabs and make sure the are lined up Perfectly on each side or you will repeat until its perfect, and this is done by hand, the feeder will not straighten it for you if you start it even a little bit off line. I was able to print out all the pictures you see on the rack (13 )with the starter inks, I ran out of light grey first then light vivid magenta. I got 4 prints after the light black low prompt came on the little screen on the printer, the computer will tell you well before that. A bit to much play in some of the plastic covers, and the feed tray cover on the front feed Must be closed each time after you feed it before you print. It will load but will not print until closed but there is a prompt to do so. Maintenance box is about 15 percent full after all these prints and setup, so with an extra box included you have plenty of time, most came form initial setup of inks. I actually think its faster than the average review says, but I have never been a production printer and I usually do not print border-less, I mat my most of work and its just covering up Very expensive inks. The little screen is very well thought out, bright, clear and menu items easy to find, its a touch screen that swivels up but Its tight enough and does not move when you use it. I will edit this if I find anything that may be of use. I am glad to have it,.... and as ALWAYS.... very pleased with the way B&H provides the best shopping experience available online or in store....

I like the size of this insert. It fits nicely into all my front loader backpacks, so I'm not limited to a "photo backpack ". Also it is just right for my z7, 15-30, 24-70 and 70-200 all f/4. Plus batteries and a few filters.

I purchased the Back Loader but I did not like zipping it up and flipping it over to access the front panel. The Font Loader works. For Travel with 2 camera bodies, lenses, drone, mics and accessories the Pro Light Front Loader is great.

I use this stand to mount mic wireless receiver, tube pre-amp, DBX PX, and mixer.Pros: Solid build. Beautiful black finish. All fits perfectly. The included nuts fit so well to the stand. Mixer mount can change angle which is nice to control the mixer during gig. Still have extra space for another mic wireless receiver, and 2 rack mount power surge protectors.Cons: No washer included. Since the nuts without washer will damage the equipment, I have to get the washer from local @ store.

I just received my ION and will be using it this weekend for a wedding shoot. While I haven't had real world experience with it my testing in the studio has all been positive. The ability to throw a lot of light with my strobes vs. trying to bounce a speedlight off a cocktail napkin will open up a new world of possibilities. For some reason I find myself doing a lot of Golf Course weddings and being able to go cordless should be very helpful. The quality of the product is great. It recharged quickly and it doesn't weigh much so moving it around is a piece of cake. The only caution I'll throw out is that the bracket that attaches to your light stand may need some adjustment before you try and mount the battery. The screw that holds that bracket to the stand has a washer that I assume is intended to protect the light stand. There's a screw that holds it (the washer) to the bracket and mine wasn't screwed in fully. When I tightened that bracket to the light stand the screw head put a nice dent and scratch in the stand. Not the end of the world but slightly annoying. Other than that, all good and well worth the investment.

Someone please tell me any other film washer better than this.

Just what I needed to use my top loader with my action x.

Grips onto stand from two Velcros in back, and in front, from both sides the bottom,

- all fits just great - very confortable dividers - Top Loader makes accesibility easier

great quality, durable, and zero's in very easily. Ready for muzzle loader season!