Get Power From Ethernet Cable Adapters

You can buy less expensive ethernet adapters for your Mevo, but I'm glad I got this one. I wasn't sure if I could run power as well as connect to ethernet to stream church services. This works great.

I purchased the two-pack Actiontec Bonded MoCA Network Adapters after reading about them online. They are extremely simple to install. All you do is connect one to your tv cable and plug in you ethernet source and you're ready to go. You must have at least two adapters to complete the network. I installed the second one in our living room. This time I just connected the tv cable to the adapter and it was the ethernet source for my streaming devices. I was so satisfied with these adapters, I purchased the wi-fi extender with which I am equally pleased. I've gotten over 100 Mps with this wi-fi extender - unbelievable!! If you need a hard wire ethernet in your house, this is the simplest way to get one - using your existing cable tv lines. I decided to cut the cord on cable tv because my bill went up nearly $20 per month with no change in service. With this device, I am able to run OTA TV and streaming devices over my home tv cables and it's like magic. I definitely recommend this produce to anyone interested in a MoCA network.

This is by far the best non-Ethernet home networking solution on the market delivering near 1G Ethernet speeds.� There were some teething issues for me that I had to resolve, but since then my three adapters have been rock solid.� So much so I just bought 2 more. A few tech notes from the issues I had to resolve.� High frequency bandwidth is everything for these adapters.� Make sure you have RG6 wires, this should not be an issue if using cable wiring preinstalled in the last 30-40 years or more recently by the cable company.� In my case the in wall wiring was OK with RG6 cable.� However a previous owner had used cheap R59 jumpers (with cheap twist on terminations) between a rat's nest of cheap Radio Shack splitters that couldn't pass more than 1 GHz.� I bought a higher quality 6-way splitter rated up to 2 GHz.� I also found that having a filter designed to contain the MOCA signals within the house was an absolute necessity.� This filter is installed at the input to the splitter for me.� I think the filter either addressed a high frequency impedance issue or controlled signal reflections that were causing issues.�� As an aside to anyone who cares, these adapters do pass VLANs and probably any other Ethernet L2 items like jumbo frames and the like.� I believe all MOCA adapters do is to encapsulate Ethernet frames and seamlessly pass it over the MOCA network.

This is the way to go if you want to expand the bandwidth of your home network without running ethernet cable, and IMO is far superior to powerline adapters. They are truly plug and play, and require no setup at all once correctly connected to your router. My home was built with coax running to each room. I bought the 2 pack of these adapters to get more bandwidth for media streaming to my TV, and I am getting close to the advertised gigabit speeds. Just make sure you also buy a MOCA POE filter or else your data will travel out of your house into the cable network ... they are cheap so buy one and save yourself the headache. Also, these are not compatible with satellite TV .. only cable.

Not much to say about an ethernet cable, except that it works.

Comes with phone cable, Ethernet cable, coax cable all of high quality. This is one of the highest joule rated surge protector. I'm going to buy another one... This is my second. The other one is on my entertainment system with a ton of power blocks and cable. Ohh... Did I mention this has an electric noise filter? A great feature for those sensitive electronics and will notice cleaner audio from your speakers. Plenty of power outlets never have to worry about having enough jacks.

Used this for a elevator camera conversion. This allows you to use a single BNC coax cable to power and connect a Ethernet POE camera. You only need to supply 24vdc to the near end converter. It also extends the operational distance limitations. very nice

I have this wifi access point mounted on a high wall in the central part of the house; it easily provides coverage to all rooms (4000' feet home). You need to have access to an ethernet cable and you must be able to provide power over ethernet or be able to use the included power injector somewhere along the cable run. It works very well and is fairly easy to set up, but it's not a home handyman type of thing.

Now that I am working from home, I want to be able to plug an ethernet cable directly into my MacBook Pro. And a USB microphone. And the power cable. But my MacBook has only two USB-C ports. The EZQuest hub also means I don't need adapters for the ethernet cable or the cord from my external microphone. I did a lot of research before choosing the EZQuest. It has all the features I want, including the most up to date USB 3.1 ports and USB power delivery 3.0 for the fastest charging. The quality is excellent and it's more compact than I expected expected. Even the color goes well with my MacBook!

Short Ethernet cable that works.