Insignia Usb Powered Bluetooth Audio Transmitter

When teamed with a BlueSENSE Bluetooth audio transmitter, I've got great sound anywhere in my house. Easy to set up and great sound with my Yamaha receiver and CD player!

I use this thing everywhere there is a USB powered plug.

Never had a USB hub go south on me before, but my Insignia apparently did. Suddenly every hour or so one or the other drive connected to it would disconnect and reconnect -- and sometimes would stay disconnected. This was after several years of trouble-free service. I had a hard time believing it was the hub, since that never happened to me before: How can a hub go bad??? Finally I bought this Xcellon hub and WHOOSH! all problems disappeared completely; can't recommend it highly enough.

Used to remove usb ground loop noise on a bus powered audio interface. Worked perfectly.

The speaker squeezes a few functionality under the same roof for a fairly low price. It has bluetooth, SD card reader and USB playback. It also has USB recording which is surprisingly a rare feature in audio equipment. The only other model that I found having this feature was Fender Passport Venue which is much more expensive. It is a surprise that it's such a rare feature --- it's the 21'st century for goodness sake! The speaker has a 3 channel mixer which is fairly good for me. I am connecting the Left/Right output of my mixer to the L/R inputs. The speaker mixes these two into one channel. I occasionally connect the bluetooth of my iPhone or iPad to it and use it to play back. I am no expert in audio equipment. I am a simple occasional user who needs something of a fairly good quality, and this has so far given me what I wanted. Although I am wondering if the 15 version of the same speaker sounds any better. It has wheels and rubber or synthetic pads underneath that make it very easy to move on a hardwood floor. It has handles on the top, and on both sides which make it very easy to carry. The casing is nice but not tough. If you often need to carry it to venues, wrap it, secure it or use a carrying case.

Up until now, I could connect either a USB-audio headphone OR a USB-compliant MIDI keyboard to my USB-C iPad via a wired connection, but not both. This meant that one of the two – keyboard or headphone – had to be connected via Bluetooth. This is usually not a problem except when trying to record a live performance, where Bluetooth latency is frankly unacceptable. With the MiniFuse, however, both the keyboard and the headphone attach to the interface, and a single USB-C cable connects to the iPad. I have so many neat synth and other music creation apps on there that I can finally use live! This is HUGE for me. Note that the MiniFuse 4 supports up to 500 mA keyboards via its USB-hub, so long as it's plugged in, whereas the MiniFuse 2 supports only up to 250 mA devices, which cuts out most external USB-compliant MIDI keyboards. Yeah, it's a bit of a pain to have to plug the MiniFuse 4 to a wall socket to make it all work, but that's still just a single wire. Oh, also, I've connected some synths to the audio inputs, and I've been running both the headphone and main Audio outputs, as well as the loopback interface both with the iPad and my mac, and it all works and sounds fantastic. The manual takes a bit of careful reading to understand the possible routings (for me at least, I'm a newbie at this) but it's well written and I was able to figure it out pretty quickly. I didn't know I needed it, but now that I have the MiniFuse, I can't imagine not having it as the central hub to my synthesizer setup.

Good value for a powered USB hub. Works for me.

Polk Audio XT10 Powered Subwoofer is replacing an Advent 12" powered subwoofer that is nearly 20 years old. The Polk unit is smaller than my older unit and it puts out a cleaner and crisper sound. Setup took less than 5 minutes. I am using this for few more days before I make any volume adjustments, if they are needed. This is a great unit for the price!

I wanted a video transmitter for the Ronin S and this works great. I powered the transmitter directly from the gimbal so I could use the battery mount to fix it to the SmallRig frame using a 3D printed part and it works great. A short 6 HDMI cable is the perfect length.

Excellent battery life. We powered an EX3 and a Teradek 2000 transmitter. Ran for 2 hrs.