Large Front Loader Washer

Received today, I wont get to deep in the unboxing as its very easy and the paperwork is child proof. It all fit together and even shows you where on the cartridge to put your finger pressure when replacing the ink for best results. A few things to think about. First I used ultra smooth fine art paper from Epson, it will feed through the top loader sometimes, though much more consistent in the front loader. BUT...It must be Very straight, use the lines on the entrance tabs and make sure the are lined up Perfectly on each side or you will repeat until its perfect, and this is done by hand, the feeder will not straighten it for you if you start it even a little bit off line. I was able to print out all the pictures you see on the rack (13 )with the starter inks, I ran out of light grey first then light vivid magenta. I got 4 prints after the light black low prompt came on the little screen on the printer, the computer will tell you well before that. A bit to much play in some of the plastic covers, and the feed tray cover on the front feed Must be closed each time after you feed it before you print. It will load but will not print until closed but there is a prompt to do so. Maintenance box is about 15 percent full after all these prints and setup, so with an extra box included you have plenty of time, most came form initial setup of inks. I actually think its faster than the average review says, but I have never been a production printer and I usually do not print border-less, I mat my most of work and its just covering up Very expensive inks. The little screen is very well thought out, bright, clear and menu items easy to find, its a touch screen that swivels up but Its tight enough and does not move when you use it. I will edit this if I find anything that may be of use. I am glad to have it,.... and as ALWAYS.... very pleased with the way B&H provides the best shopping experience available online or in store....

I like the size of this insert. It fits nicely into all my front loader backpacks, so I'm not limited to a "photo backpack ". Also it is just right for my z7, 15-30, 24-70 and 70-200 all f/4. Plus batteries and a few filters.

I purchased the Back Loader but I did not like zipping it up and flipping it over to access the front panel. The Font Loader works. For Travel with 2 camera bodies, lenses, drone, mics and accessories the Pro Light Front Loader is great.

I bought this to use while backpacking. On a recent 7 day trip it worked really well. It has just what I need and nothing I don't. It's really light but seems durable. The double zippers are easy to open and close with one hand, even then the case is empty or overfilled. The lid/opening is large and opens away from your body so you don't lose things and keep dirt out of the case as much as possible. The design keeps a low profile, it doesn't stick out away from your body very much which is very nice for hiking in the woods on narrow trails and lets it hang more comfortably. The variety of different attachment points is very handy. Most of the time I slipped the two main loops over my backpack waist belt. I learned from experience that I needed to use a small carabiner clip to keep the camera loader from slipping off the waist belt when I took my backpack off (almost left the camera behind by accident at a rest break in dim light! The camera loader had slipped off the waist belt when I put my pack down to get out my headlamp and I was too tired to notice it until we were down the trail a ways) Once I figured this out the extra small attachment loops made it easy to use as small bit of rope and a small carabiner to secure it. At other points I used a loop of shock cord to secure the camera loader around by waist when I was hiking around without my large pack on. I was shooting with a Sony A6000 with 16-70/4 and had room for the Samyang 12/2 in the bottom of the case and 2 spare batteries in the internal zipper pouch. This kit fit very nicely in the case and was easy to take out and put back in. I like to have my camera sitting sideways in the case so the grip is facing up. The internal velcro divider is perfect for putting a second lens at the bottom of the case.

It's great changing bag for large format 4x5 and bulk loader. satisfied with fast delivery from B&H

This 12 Floodlight Reflector by Impact is perfect for 2-3 light setup. This item is very light and easy to install without problems. Their is no negative comments about this product. When installing the reflector with the Impact socket ceramic lamp holder, make sure you place the supplied 1silver washer inside the reflector before you screw it in place with the supplied large aluminum nut(type) the goes over the ceramic socket. When you do place the 1 washer outside behind the reflector, screwing the aluminum nut(type) will be difficult. although small hands can get it tighten, but large hands will be a problem.

Screws into one of the centre holes on the plate, but it's a bit long, so I added a large SS washer and it also prevents any gouging on the plate, etc. I'm amazed at how powerful a grip the quick-release has on the ball head. No slippage, even with 100-400 or 200-600 lenses.

Someone please tell me any other film washer better than this.

Front pocket is large enough for a keyboard and mouse.

Just what I needed to use my top loader with my action x.