Linux Usb Ethernet Adapters

Unlike some other USB to Ethernet adapters, this one indicated GB speeds and actually delivered them. Easy setup and to use.

Totally reliable so far. Wish it did not cost so much more than all other USB-C to Ethernet adapters, but I bought three, so it's obviously worth it to me!

I' use these for Linux distros, for me its better then USB drives...

Not much to say, it's a USB to Ethernet adapter. Works exactly like you would want it to.

This adapter works well with Linux, but will require the user to compile the open source driver and install it. Careful instructions are on the web. I use it on a workstation normally attached to ethernet, but occasionally in need of wireless access. Quick speed test on a strong signal was about 250Mbps (650Mbps on ethernet).

Very happy with the MB supporting an AMD 7950X. Bios memory battery was dead on arrival. Linux support is a bit rough at the moment. I had ethernet failures until I found: https://www.reddit.com/r/buildapc/comments/xypn1m/network_card_intel_ethernet_controller_i225v_igc/ Linux audio not is passing through the S/PDIF at the moment.

[This review was collected as part of a promotion.] The Belkin USB-C to Ethernet + Charging adapter is amazing tool to have with you when you need an ethernet connection. The USB-C to Ethernet + Charging adapter charges your connected device while also providing an ethernet connection, so no need for multiple connectors. I have been using this on my Android phone and my laptop, both devices have a USB-C port and my Belkin adapter worked great on both devices. It provided an adequate charge and a stable internet connection without any issues. The adapter was immediately recognized by both devices and there was no need to install any software to make the adapter work. The adapter is also small and portable enough to carry with you anywhere you go. I would highly recommend this adapter to anyone looking for an ethernet + charging adapter.

I purchased the two-pack Actiontec Bonded MoCA Network Adapters after reading about them online. They are extremely simple to install. All you do is connect one to your tv cable and plug in you ethernet source and you're ready to go. You must have at least two adapters to complete the network. I installed the second one in our living room. This time I just connected the tv cable to the adapter and it was the ethernet source for my streaming devices. I was so satisfied with these adapters, I purchased the wi-fi extender with which I am equally pleased. I've gotten over 100 Mps with this wi-fi extender - unbelievable!! If you need a hard wire ethernet in your house, this is the simplest way to get one - using your existing cable tv lines. I decided to cut the cord on cable tv because my bill went up nearly $20 per month with no change in service. With this device, I am able to run OTA TV and streaming devices over my home tv cables and it's like magic. I definitely recommend this produce to anyone interested in a MoCA network.

This is by far the best non-Ethernet home networking solution on the market delivering near 1G Ethernet speeds.� There were some teething issues for me that I had to resolve, but since then my three adapters have been rock solid.� So much so I just bought 2 more. A few tech notes from the issues I had to resolve.� High frequency bandwidth is everything for these adapters.� Make sure you have RG6 wires, this should not be an issue if using cable wiring preinstalled in the last 30-40 years or more recently by the cable company.� In my case the in wall wiring was OK with RG6 cable.� However a previous owner had used cheap R59 jumpers (with cheap twist on terminations) between a rat's nest of cheap Radio Shack splitters that couldn't pass more than 1 GHz.� I bought a higher quality 6-way splitter rated up to 2 GHz.� I also found that having a filter designed to contain the MOCA signals within the house was an absolute necessity.� This filter is installed at the input to the splitter for me.� I think the filter either addressed a high frequency impedance issue or controlled signal reflections that were causing issues.�� As an aside to anyone who cares, these adapters do pass VLANs and probably any other Ethernet L2 items like jumbo frames and the like.� I believe all MOCA adapters do is to encapsulate Ethernet frames and seamlessly pass it over the MOCA network.

You can buy less expensive ethernet adapters for your Mevo, but I'm glad I got this one. I wasn't sure if I could run power as well as connect to ethernet to stream church services. This works great.