Removing Seal From Front Load Washer

[This review was collected as part of a promotion.] Must be careful removing the seal to install. It tend to leak and make a real mess.

Cabinet was easy to set up. It's sturdy and you can feel how well the front door seal holds. I store mostly filament, and there's a drastically lower amount of moisture creeping into my test spool over the last month.

Someone please tell me any other film washer better than this.

I can take off and put on the cap without removing the len's hood. Thus keeps the len's front element free of dirt.

I bought this to replace a Tiffen filter that I had occasionally used on a Canon 24-105 F4L. The Tiffen was junk, plain and simple. The only thing it was good at was being a barrier in front of my main lens element. I found myself removing it more often than not however because it had a notable effect on IQ. So, I ponied up and bought this. The difference is night and day. When holding the B+W in front of your eye at arms length, it is sometimes difficult to determine if there is in fact any glass in the filter at all. The brass mounting ring is very tight tolerance and took some effort to properly line up the threads. It is tight and very secure and I don't think I will be removing it any time soon. I will be buying more B+W filters to place on all my lenses.

Load everything up and move it from one location to the next. All my equipment fits perfectly. Collapses down to fit in the front seat area of my car, with the wheels on the floor. Don't need a truck just yet.

I haven't actually used this yet, but I did load it, weigh it, and pretend to put it in an overhead for practice. Seems perfect for my gear. I travel with a DLSR, mirrorless and 4 lenses. There is room for that and a change of clothes if a bag gets delayed. The front compartment easily holds my 15 laptop. The laptop compartment sort of locks by attaching the loop on the zipper to the integrated lock for the case (watch the video). The case rolls easily. I agree with the reviewer who said it would be nice if the bottom of the case was flat, but with my gear that is not a problem. The recommended accessory GRID-IT organizer of 10X12 does not fit the interior front pocket and looks like it has been removed as a suggestion. All-in-all this looks like it will be a great bag. It will be my carry-on but seems sturdy enough to gate check on smaller planes.

I couldn't be happier. This cart rolls over anything and carries all my gear. The only slight problem is if you load the rear with more weight than the front, the front wheel wiggle and increase resistance to push. Design questions, changes... why not make the deck a bit wider. It would allow for more gear between the hands (light stands, tripod, etc), and since there are wheels blocking the bottom rail, put something to hook onto for bungee cords.

This is a great day/travel bag for taking your camera and a spare lens. To me, it's one step up in complexity/organization from a peak design neckstrap, which I also have and use, for days when you want to grab the camera, but also second lens and extra battery. The bag wears comfortably, wraps around your back when not in use, swings around to the front, and you can wear it as a fanny pack (though I haven't). There are nice little nooks and crannies for extra batteries, cords, etc. The flexibility and capacity of the bag is a double-edged sword. Yes, you CAN load it up, a lot, and if you are flying somewhere and need the capacity, it's there. You could do an 80D with a 18-135, two pancakes on one side and an 85mm on the other, and have room to spare for more. But, if you really load this up to maximum capacity, it starts becoming like a traditional heavy camera bag, a psychological and physical burden that detracts from actually leaving the house, being mobile and taking out your camera quickly and actually using it. Just my thought process. One less that great thing... the front pocket is a little hard to access, for me, especially if the bag is full. It could have been made just a tad more roomy, maybe with some more give on the sides. As is, the cloth is very tight and you kinda have to pull it apart and plunge your hand across a sharp-ish zipper to get in there. Know what I mean? Maybe the next generation addresses that.

Perfect for what I need it for, very rigid and the seal is spot on.