Wire Headphones Into Speakers

This cable adapter is enabling me to use my old wire headphones.

I use these headphones for mix n mastering. The wire they come with also works for the K240 MKII headphones as well.

The sound is unbelievable The Bluetooth makes it very exceptional for placing the speakers in where you need no more wire that's just awesome.

I bought these Sony Dolby Atoms speakers a few months ago and I more than happy, they look and sound great. The build quality is great the speaker box been wrapped with a flat black vinyl wrapped and looks amazing, on the back the speaker wire input are wire clips sorry no banana inputs, also I was very surprised how heavy these speakers are, trust me they have some weight to them. I believe the maximum watts are 100 and the Ohm's are 6. Just match these babies with the Sony tower speakers and you are good to go..

I used these speakers with JBL 19cs subwoofers for a weight room facility sound system. The total system consisted of 6 - 26c speakers and 4 - 19cs subwoofers. Wiring is made easy with the removable terminal blocks and passthrough wiring. Basically each speaker connects to each other in a line. This installation method reduces cost for speaker wire and labor involved with running extra wire. The terminal blocks have 4 wire holes. For the first speaker in the line will use holes 2 & 3 for the line connecting to the amplifier. Then a wire is ran from speaker 1 to speaker 2. Holes 1 & 4 from speaker 1 connects to holes 2 & 3 on speaker 2. This continues for the entire line. Be sure to properly power these speakers. Both the 19cs and 26c need 140 watts of power. In our installation we used 2 amplifiers splitting the system into left and right sides of the room. Since each amp had 2 outputs of 500 watts for each channel. This provided some headroom for the speakers. On both amps output 1 was was the high and output 2 was the low. Output 1 had 3 26c speakers and output 2 had 2 19cs subwoofers. These amplifiers had a built in crossover feature that splits the signal into high and low frequences which is essential for installing a system like this. A xlr splitter was used to convert the output from the mixer (1 xlr) to inputs for both amps (2 xlr). A cutout template is provided for cutting ceiling tiles. Once tiles are put back in the ceiling the installation can be done without access into the ceiling. The speaker is designed to push up through the cutout in the ceiling tile and clamps down to the C bracket (included). Make sure to have someone assist with installing, these can be insalled with one person but can be difficult for one person to lift, attach wires, put into place, and screw down holders. Overall these speakers work as expected and would buy again. They install nicely and end product looks professional. Nothing less to be expected from JBL.

I placed this amp in my basement and ran speaker wire outside to a pair of Polk audio atrium 8 speakers. Sound is amazing and so convenient to stream music every time I walk outside. I did a lot of searching and finally settled on this combo. Loving it. Highly recommended!

We use these Bogen WB1EZ wall speakers on our paging system. They are easy to wire up with only two wires and work well.

This was my first Sonos and I really love it. We renovated our great room and was going to wire it for speakers. We decided to get Sonos instead and are extremely happy with the choice. The sound is fantastic - rich, powerful, hits the highs and lows. I stream from pandora and from our large collection on iTunes. We liked it so much we sprung for a 3 and 1 for two other rooms a few months later.

No doubt, it's spendy; even in the Sonos realm. Said it, now it's out of the way. I have been super happy with the Amp since day one. Shipped fast, great packaging, everything I needed to install and set up, and quality is evident straight away. I had Zone 2 speakers in the back porch ceiling that were controlled via an AVR. Always cumbersome to turn it on and then it was picky about which sources would feed to Zone 2. Enter the Amp. HDMI, optical, and WiFi inputs; input source issues solved. I pulled the speaker wire from the AVR and installed the INCLUDED banana plugs. Plugged in the Banana plugs, ethernet cable (it was handy, why not hard wire?), and then the AC power. Start to finish, 7-ish minutes. That includes cleaning the 6 years of dust bunnies that were stashed away within wire runs. Solid, sounds great, and real easy to use. Tell Siri to play "The Pool Day" playlist on the patio = DONE! Gripes? Wish we could run TrueSound calibration with in-ceiling speakers of our choice. We bought the amp, it contains the EQ, not the speakers. I would still buy another one though.

Great for hooking up bi-wire floor speakers for the best high fidelity sound available from your receiver.