Check the wiring integrity of your grounded power outlet with the TES-122 Receptacle Tester from Platinum Tools. The unit is designed to test 110 to 125 VAC outlets and features two amber LEDs and a red LED that light up in various combinations to indicate up to 5 different faults or if the wiring is correct.

Detects Problems in 3-Wire Outlets    Tests 110 to 125 VAC    3 LEDs Light Up to Indicate Problems    Detects 5 Possible Faults

• Open ground
• Open neutral
• Open hot
• Hot/ground reverse
• Hot/neutral reverse

Related Questions and Answers

Q: 1. Can this be used as BOTH a source and display emulator at the same time to test a cable? It says it can be a sig gen OR display

A: According to the manual, there is no mention of dual operation being impossible at the same time when using the Vanco Handheld 4K HDMI Tester.

Q: 2. Will this test UPS/APC batteries?

A: UPS BATTERIES ARE SEALED LEAD ACID (SLA) BATTERIES, ZTS HAS OTHER TESTERS FOR SUCH BATTERIES, NOT THIS ONE.

Q: 3. Does the CBT-12 send test tone?

A: Yes, the Kopul CBT-12 can provide a test tone.

Q: 4. Why are AAA,AA,C,D Alkaline batteries tested on the same point? How does it know battery size to test with different current?

A: We are not aware of the exact reasons or engineering behind how the ZTS MBT-1 Multi Battery Tester works in the way that it does. At the time of this posting the product has a very high review rating and works well for those who purchase it.

Q: 5. Does the CT-3 have a built in speaker or a headphone jack to monitor incoming line/mic level audio signals?

A: In addition to its onboard lights, the dbx CT-3 Advanced Cable Tester uses a test tone generator which sends signal out of the jacks on the left side of the unit. The Test Tone generator is strong enough to drive certain devices directly for testing without additional power. For example, a speaker may be directly connected to the CT3 and the 1KHZ tone may be heard from the speaker. Headphones can be directly driven, as well as telephone lines. The unit does not have a built-in speaker.

Q: 6. how much weight can the table top hold?

A: The MFR does not specify. It is a posing table it is meant for elbows not heavy loads.

Q: 7. Will this work for button cell batteries like A76 and other film camera batteries - 28L, Wein cell 625... ?

A: I dont think that your A76 camera battery can be successfully tested on the ZTS Mini Multi-Battery Tester MFR # MINI-MBT. The specifications are: 1.2V NiMH / NiCd rechargeable (AA, AAA, C, D) 1.5V alkaline (AA, AAA, C, D, N)3V photo lithium (CR123, CR2) 9V alkaline and carbon zinc3.6 V lithium-ion (18500, 17650, 18650, RCR123A)And according to this website, your A76 is 1.55 volts, so maybe you could use the 1.5 alkaline post? But the 28L is a 6 volt Manganese Dioxide Battery.medicbatteries battery-cross-reference-guideBut take a look at another ZTS product; MBT-1 battery tester That will test the A76.

Q: 8. Will this test 3.6v Lithium D Cells (XL-205F)?

A: Unfortunately it cannot.

Q: 9. What material is the table top?

A: The top of the Impact Posing Table - 28-48" (71-122 cm) is plastic.

Q: 10. Is the table top easily removed from the base for transport?

A: The table top can be removed but I would not classify it as easy. The table top is secured with 4 screws. It was not designed to be repeatedly detached and attached. Doing so could damage the taps and cause the table to be unstable.