Audio professionals looking for a bag to carry a wireless mic system will be impressed with the Auray WSB-1S, a lightweight padded nylon carrying bag designed to hold and protect a single microphone wireless system and accessories. The bag allows you to easily transport your audio gear to and from a shoot. The case can be carried over the shoulder while you follow the action, ensuring that you're never out of microphone range.

The bag features a dense foam interior with precision cutouts that prevent the receiver, transmitter, microphone, and accessories from rattling around during transport. You'll have total access to the front and rear of your receiver, allowing you to adjust audio controls and cable connectors. And there's plenty of storage room, as well as an accessory pouch to keep your cables, batteries, lavalier mics, and mic clips organized. The lightweight nylon exterior offers protection from moisture, dust, and debris.

Fits Single-Mic Wireless System    Fits Receiver and Transmitter    Mic Cutouts    Unobstructed Access to Front of Receiver    Rear Access for Cabling    Accessory Compartment    Ample Space for Antennas    Includes Shoulder Strap

Everything your sound engineer needs for a location shoot can be transported safely and comfortably in the Auray WSB-1S. There's room for a receiver, bodypack transmitter, handheld microphone, and accessories, such as lavalier mics, cables, and batteries.

The dense foam pads are custom cut to fit your important audio devices and protect them from accidental bumps and shocks while traveling and during field recordings. Your receiver, transmitter, and handheld mic will be padded and held securely in place.

The zippered front flap keeps your transmitter, receiver, and mic protected against the elements, as well as dust and debris, until you're ready to go to work. Then, you can unzip the flap and have complete access to the receiver's front panel. There's zippered access to the rear panel too, so you can run cables to and from the unit without any obstructions.

There's a generous accessory compartment where you can stash cables, batteries, lavalier mics, and other accessories you need for the shoot. Put them all in the included accessory pouch to keep them organized and easy to find once you're ready to set up.

The bag is constructed with enough space in the rear compartment to accommodate a receiver's antennas, whether they're built in or attached separately.

Subjects can very easily move out of your microphone's transmission range. Say you're recording narration while your subject is hiking a trail or running up a football field. Throw the bag over your shoulder and keep up with them, so they'll never be out of range, and you'll get every word.

Related Questions and Answers

Q: 1. How far apart are the feet when the legs are not extended?

A: This question is a little tricky, as the legs can be unlatched to fold flat, if desired. However, assuming that you go from a completed folded state, to just opening the legs, and not extending them or further allowing them to spread, then they are 19.5 inches between the outer edge of the rubber pad on each foot. The tripod fits on a platform as small as 18 inches deep by 19.5 inches wide.

Q: 2. If I wanted an unpadded Manfrotto bag, which size would be ideal for this tripod?

A: I purchased a padded 31.5 manfrotto bag and it fits perfectly. In my opinion, it's worth it to spend more on a padded bag. Manfrotto MBAG80PN Padded Tripod Bag.

Q: 3. Does the Manfrotto 438 Compact Leveling Head works with the tripod and fluid head offering in this kit?

A: Yes it does. You can install B&H # MA438 between the Tripod and Head in this kit.

Q: 4. I just purchased the MVH502A. A review shows you can screw the 3/8-16 screw into the side. Of course I use that one. Any place to screw the 1/4-20 screw? Both sides only seem to fit the 3/8-16.

A: If you wanted to connect a product with a 1/4 to one of the 3/8 threadings on the side of this tripod you could look in to a reducer bushing. B&H number OB1039 is the Oben 3/8 -16 to 1/4 -20 Reducer Bushing and is a good choice for this function.

Q: 5. Does the head come off?

A: I have this tripod and yes it does come off... I've placed the head on sliders

Q: 6. Will this work with Panasonic AG-DVX200?

A: Yes it will. The 502HD head has a 15.4 pound load capacity, which is more than enough to handle the DVX200.https://bhpho.to/2cLklsC

Q: 7. Does this QR plate fit with the Glidecam 2000 QR plate?

A: If you get the Glidecam that comes with the 577 adapter, then yes.

Q: 8. it is a half ball system? or is complete?

A: The 502HD Fluid Head has a ball base that is a hemisphere. It fits into the concave bowl that's atop the tripod legs. Thus they they work together in complete coordination. It is our preferred combination for video tripods.

Q: 9. Does this tripod work well with a Sony a7rii? Does it include a compatible quick release plate?

A: It works well with DSLRs. I use it for bigger cameras to great effect. It doesn't have a quick release place, just a typical tripod plate. We use VCT plates though so that gives it a quick-release functionality. The tripod plate connects into the VCT baseplate.

Q: 10. So is it MVK502AQ or MVT535AQ tripod?

A: This is the MVK502AQ tripod.