The SURVEYOR Moisture Alarm, Vacuum Valve & Pump for Nikon D810 from Aquatica offers an added level of protection to the underwater photographer. The SURVEYOR circuitry integrates a water detection function that remains on constant duty when a battery is inserted. Should the slightest amount of water make contact with the sensor probes, it will trigger an alarm using both an audible signal and a rapidly flashing red LED to visually attract your attention. Adding the vacuum pump and pressure valve to your housing will make it possible, by creating a vacuum inside the housing, to fully test its sealing integrity. Once the easy-to-follow procedure is completed, a green LED blinking every five seconds will inform you that your SURVEYOR system is monitoring your camera housing and you're ready to dive. In the event that sand, hair, or other foreign matter would compromise the housing sealing integrity, the SURVEYOR warns you with both an audible signal and a rapidly flashing red LED signal.

This kit includes the moisture and vacuum sensor circuit, a pressure valve with retaining nut, a vacuum pump, mounting hardware, a container of O-ring lubricant, and a CR2032 battery.

Red Flashing LED When Water is Detected    Vacuum Pump to Verify Seal Before Dive

Related Questions and Answers

Q: 1. Will this grip also enable more frames per second in CH mode on my D800 like the Nikon MB-D12 grip?

A: The Vello BG-N7-2 Battery Grip for Nikon D810, D810A, D800 & D800E can increase the frames per second. You have to use the EN-EL18d battery and a different cap. B&H # WAENEL18DCK (B&H Kit) includes both.

Q: 2. Do I really need Pluto trigger along with valve? Can the Valve be programmed independently to drop water?

A: You would need the Pluto trigger for water drop

Q: 3. Can the pluto valve and trigger be used without connecting it to my camera? Can I put my camera (Nikon) on(CH) high speed release and fire away as the drops fall?

A: You can do continues high speed , but you would miss a lots of shots and if you are using a flash to freeze the water drops you will have a very difficult time catching them at the right time

Q: 4. Can it work with canon M5 or canon 5 D IV?

A: Cant see why not. Its connected to the pluto trigger and not the camera directly. I have a 5d mark iv but i have not used this part yet. It will work

Q: 5. Hello, will the Pluto valve with a Pluto trigger work with a Pentax KP that does not heave IR remote capability? Thank you

A: To use this with the Pentax KP you will need this cable VERCCC125 as well as this adapter HOASSMFSMM. The remote port on the KP is a 3.5mm which is why you need an adapter. -The adapter will go into the camera. -Then the cord goes into the adapter - Then the other end of the cord goes into the Pluto Trigger.

Q: 6. For those of you that have the Pluto trigger and valve, what settings do use to achieve the mushroom type effect??

A: Pluto Triggers does offer a value guide on their site specifically for shooting water droplets.

Q: 7. Can the Pluto Valve be triggered by plugging the cable into a MIOPs Smart or in any other way that does not require the Pluto Trigger?

A: The Pluto Valve's performance is only warranted with the Pluto Trigger.

Q: 8. Besides a camera and speedlights, what all do I need to purchase to use this....I know I'll need the Pluto valve and Pluto trigger, but what stands and cords do I too need to get?

A: I would recommend calling in and speaking with a sales professional to talk about your options. Every shooting situation may require different equipment. 800-947-9950.

Q: 9. can this be set up with a Sony a5100, assuming you have the trigger and speedlights?

A: You would need the Pluto trigger to work in conjunction with the valve. Click the link below to view; https://bhpho.to/2ZdQpdq

Q: 10. DOES IT WORK WITH NIKON 1 j3 ?

A: Yes, it will work with the Nikon J3.