This black, 2' RG8X Low-Loss Coaxial Antenna Cable from RF Venue is a 50-ohm cable that features BNC connectors and offers a cost effective, reliable interconnect. The cable is constructed with a double-shielded braid over foil to provide the right balance between loss and flexibility. This cable comes in a 10-pack bundle.

BNC Connectors    50-Ohm Cable

Related Questions and Answers

Q: 1. Are they still compatible with the Bolt 4k series?

A: The Teradek 6G Flexible "Mushroom" H Antenna Kit for Bolt 6 antennas can be used on the bolt 4k series as long as the operating frequency is 5.8 GHz. The Teradek 6G Flexible "Mushroom" H Antenna Kit for Bolt 6 antennas operate from 4.9 to 7.3 GHz.

Q: 2. Can you combine IEM and IFB RF signals of different output strengths? For instance I have a Lectrosonics M2T that has two output carriers of 50mw each. and a Lectrosonics T4 IFB transmitter that outputs 250mw. Can I combine them all with this to a single antenna?

A: It is possible to use transmitters with different power output levels with the RF Venue COMBINE4 - 4-Channel Antenna Combiner. This combiner is a unity device that does not affect or change the output strength of the transmitters connected. It does, however, have a maximum input level of 100mW and would not be compatible for use with a transmitter pushing 250mW such as the Lectrosonics IFBT4.

Q: 3. Why does it not have a gain switch to account for the signal loss within the BNC cable?

A: The RF Venue Diversity Fin Antenna with Stand Mount for Wireless Microphone Systems (Black, 470 to 698 MHz) does not include a gain feature as it is a passive antenna. Active antennas can pose risks such as overloading the RF front end of a receiver system, and you can easily overload by using an active antenna’s gain control at a setting that is disproportionally strong for the cable run’s length. A good practice would be to implement passive antennas, and then only add in-line amplifiers to make up for transmission line loss if doing very long cable runs of more than 100 feet.

Q: 4. Can you use one element at a time in non-diversity mode? E.G. I want to use only the LDPA antenna on occassion

A: Yes, you can use one element at a time because there are separate A and B outputs on the RF Venue Diversity Fin Antenna with Stand Mount for Wireless Microphone Systems (Black, 470 to 698 MHz).

Q: 5. Can these be used with the Pyro S TX and RX?

A: Hollyland does not recommend using the Hollyland 2.4 & 5 GHz Thumb Antenna for Pyro 7 (2-Pack) with the Pyro S. They recommend using the following antenna for the Pyro S. Hollyland Paddle Antenna for Pyro Series (2.4/5 GHz) BH #HOHLATN14

Q: 6. Do you need to buy 2 of these or will 1 work? How many wireless receivers will 1 antenna supply RF for?

A: There are two antennae (omni and directional) in the RF Venue Diversity Fin Antenna with Stand Mount for Wireless Microphone Systems, with two BNC output connections, so a single unit will serve the function of two antennae. The number of receivers relies on implementing an appropriate antenna distribution system and is usually between 1-8 receivers.

Q: 7. Can this mount on a bag, such as a K-Tek Stingray Jr. X?

A: The RF Venue Diversity Fin has 1/4"-20, 3/8"-16, and 5/8"-27 mounting threads, but it does not have any mechanism for mounting on a bag or flat surface.

Q: 8. What are the dimensions of the diffusers? Only the dimensions of the box are given. (I want to know if theyll fit my Dracast LED 1000 lights.)

A: Dont remember but I had to cut them down just a little to fit it my elation 2000 lights

Q: 9. Do these work on both the Tx and Rx or can the stock "V" antennas remain on the Rx in combination with these "H" on the Tx?

A: When using the TX and RX for the Teradek Bolt 6/Ranger series, it is not a requirement but best to match the antennas. The Teradek 6G Flexible "Mushroom" H Antenna Kit for Bolt 6 (4-Pack) should be matched for the best performance and transmission. See this Bolt antenna overview: https://bhpho.to/3U1mCCE.

Q: 10. Does this Distro4 model feature the cascade ports to daisy chain multiple units together?

A: Yes. You can link up to four units.