The 1.8" diameter ARTEMIS Super Post Gen. 2 from ARRI is compatible with ARTEMIS Gen. 2 and TRINITY Gen. 2 stabilizer systems. This telescoping, 3.9 to 6.5' replacement center post has an inner 1.5" diameter, a 1.8" ring diameter, and a 3B 16-pin LEMO connector.

For ARTEMIS Gen. 2 & TRINITY Gen. 2    6.5' Length Enables High/Low Positions    Center Post Replacement, 3B 16-Pin LEMO    Telescoping 3.9 to 6.5' Length    1.5" to 1.8" Post Diameter

• ARTEMIS Gen. 2
• TRINITY Gen. 2

Related Questions and Answers

Q: 1. The center hole is 1/4"-20. The two horizontal threaded holes are some other size. The two vertical holes are not threaded. Outside of the 1/4"-20 center hole uses, what accessories use these patterns?

A: The smaller holes on the back of the Super Clamp allow you to connect accessories to the Super Clamp. As an example, when holding multiple backgrounds on an autopole using a Super Clamp, you may connect the Manfrotto 045 Background Triple Hooks for Three Backgrounds (Box of 2), B&H # MA045, or the Impact Background Triple Hooks - Pair (Black), B&H # IMVPDH3W, via hex screws, or you may connect a single background hook such as the Impact ME-122P Single Background Holder Hooks for Super Clamps (2-Pack), B&H # IMME122P, which may be inserted into the hexagonal 5/8" hole on the back of the unit. There may be other accessories that would also work with the attachment points on a Super Clamp, but the ones listed above would be the popular ones and the ones we carry. We do also carry Super Clamp options that have a grip head connected to the Super Clamp, or connects two Super Clamps together.

Q: 2. If the stud was oriented horizontally, parallel to a table, could the 1/4-20 screw end hold 5-10 lbs. without snapping off? If not, is there a stud like this made out of steel, like a QR plate's screw?

A: The 1/4" thread would not be stable for an item that weighs 5-10 lbs. If you prefer to use a quick release plate, the Manfrotto 323 RC2 System Quick Release Adapter with 200PL-14 Plate, BH # MA323 screwed into the Manfrotto 037 Reversible Short Stud, with 3/8" & 1/4"-20 Threads (Brass), BH # MA037 would be better. The Short Stud should have its 3/8" thread facing towards the bottom of the quick release.

Q: 3. WHAT ARE THE OUTSIDE DIMENSIONS ?

A: This Impact Super Clamp measures 1 5/8" wide by 4 7/8" long.

Q: 4. is the ratchet handle a true ratchet? or is it the same as Manfrotto's that will block you from turning the handle if you are in a tight place.

A: It is the same as Manfrottos. It is not a true ratchet. It must be pulled outward about 0.25 inches, but then it can be turned freely to any position. Just like Manfrottos, once it is in a new position it can be turned tighter or looser as needed. It requires very little room to tighten, pull out, rotate counter clockwise, push in, then tighten a little more, repeat as needed. Or loosen, pull out, rotate clockwise, push in, then loosen a little more, repeat as needed.

Q: 5. I need to clamp this to a vertical varipole and have the stud also be vertical. Is there an alternative product that does this?

A: You could this clamp in conjunction with the extension arm, click the link below to view; https://bhpho.to/31W7tHI

Q: 6. Is this compatible with the SmallHD Cine 7

A: The ARRI artemis Monitor Bracket Gen. 2 for SmallHD (7") is not compatible with the SmallHD Cine 7 as the dimensions for the SmallHD Cine 7 and the SmallHD 703 are different.

Q: 7. I'm trying to use this on a C-Stand grip head (attached to the c stand obviously) to balance my gimbal (Defy G5). Is this practical ?

A: Yes you can do that but Id be safer and balance it on a tripod using a tripod plate. Ive had one of these clamps crack in me and the weight of your camera plus gimbal may be pushing it. Hope this helps.

Q: 8. Does it come with the stud shown?

A: Yes

Q: 9. What's a good articulating arm for this ?

A: The choice of arm would depend on the item you wish to attach, the reach and level of adjustment you need when attaching to the Impact Super Clamp with Ratchet Handle BH #IMCC106R.

Q: 10. I need to mount multiple magic arms to a single clamp, are there any adapters or accessories to allow this?

A: Trying to place multiple magic arms on one clamp can easily be over the weight limit that it can handle and we do not know of the existing way do to so.