This 27.6" 2-Pin to 2-Pin/6-Pin LEMO Link Cable from HEDEN connects your CineTape control to your VLC-3 receiver via a 2-pin LEMO-type to 6-pin LEMO-type connection via the CineTape remote port and VLC-3 run/stop port. An additional 2-pin LEMO-type connector can be inserted into the YMER-3 hand unit to integrate the CineTape's distance data into its OLED display. Operating your cine camera wireless controls becomes that much more intuitive thanks to this transfer of data.

Link CineTape to VLC-3 Receiver    Integrate Distance Data into Hand Unit    Two 2-Pin LEMO-Type Connectors    One 6-Pin LEMO-Type Connector    Connects Run/Stop and Remote Ports    27.6" Cable Length

Related Questions and Answers

Q: 1. I have a 3in x 15/16" aluminum stud with a flared base that screws into my Gitzo tripod. Looking for a similar adapter for my microphone boom pole holder? Thanks.

A: Please review the two following items in order to mount a mic holder to your boom pole. The following item features a 5/8" Insert to attach directly to boom pole as long as pole features a male 5/8 screw. WindTech SMC-8 Locking Microphone Holder BH #WISMC8 • MFR #SMC-8 https://bhpho.to/304qBVi On-Stage QK2-B Quick Release Adapter (Black) BH #ONQK2B • MFR #QK-2B https://bhpho.to/3aniULQ

Q: 2. Does anyone make an extension for this cable? I want to move the unit farther from my camera.

A: If it is the cable to trigger your camera then you can either make this up yourself with a simple female 2.5mm male and 2.5mm female stereo earphone type jack plug or I'm sure these would be available at any audio type store. This is then obviously connected between the Miops and the camera cable (from Miops).If it is cable to trigger the flash, then these are available both on the flash side of the connector (i.e. between Miops cable and flash) and also as above on the jack plug side using a simple 3.5mm mono extension that either made up or purchased.

Q: 3. What Kind of camera settings do your reccomend with this device ? (Program, manual, TV or Av) my camera is a Canon 1D M.II. thank you

A: I would recommend using Manual mode, though you may wish to experiment with the other settings. Mipos website only states to set the camera to manual focus, and for shots of lightning, set the focus to infinity, and when using Sound or HDR modes, set the shutter speed to BULB. However, you would have the most control over your images using Manual mode, and then can change the aperture or shutter speed to make any changes needed to correct your initial exposure.

Q: 4. Will this work with an Insta360 one R?

A: Yes, You will need to use the mounting frame that comes with this action camera.

Q: 5. can I map the lens on this unit?

A: Yes, as per product description: A key feature of the YMER system is HEDEN's LenSaver Calibration, which provides a simple and effective way of calibrating for follow focus.

Q: 6. What is the total length of the Matthews Snap In Pin - 5/8 ?

A: Hi Dan, The end-to-end length of this Matthews baby pin is approximately 3 7/8

Q: 7. This item Is it SANSTEEL material?

A: Yes, the Matthews Snap-In 5/8" Pin is stainless steel.

Q: 8. Will this work with Canon T7?

A: The 3 pin version of this will not work with the T7. You would need the one that has the sub mini cable.

Q: 9. Can the Miops Camera Trigger work without smart phone or dongle?

A: It works without the smartphone but you must use the dongle. The single is supplied with the trigger when you order it. Just order it for the correct camera body.

Q: 10. I took digital caliper measurements of the base on my gopro 3-prong mount and it is 0.98 inches around. Is this significantly smaller?

A: The JOBY Pin Joint Mount has a base measurement of 0.91in.