Use this 1/4"-20 Thread Locknut Set from CAMVATE to add additional spacing between your camera rig and accessories. Included in this set are two locknuts with 1/4"-20 threads. They measure 0.4" at their maximum thickness and are constructed from aluminum alloy, making them durable and lightweight.

Two Locknuts    1/4"-20 Threads    0.4" Thickness    Aluminum Alloy Construction

Related Questions and Answers

Q: 1. Is there a 1/4 female thread on the bottom of these?

A: The female 1/4" thread is only found on the top of the Manfrotto 5/8'' Spigot with 1/4'' Thread for Friction Arms (Set of 2).

Q: 2. Can you tell me if the camera plate will snap into place on this clamp, or is it a slide-in like the big Manfrotto plates? Thanks.

A: First you have to open the plate up fully by turning the quickset level fully open, then you tilt your plate and slide it into one of the long side of the plate, because the plate is open, then you can push the other side of the plate into place (it will not work unless the plate is fully open). Next you close the quickset lever one notch which allows you to adjust the position, then another notch to fully lock it.

Q: 3. What is the diameter (in mm) of these tubes?

A: Each individual part from the RigWheels 6" Stand-Offs with 1/4"-20 Threads (Set of 4) (B&H# RISO14X64PC) is 6" (about 15.2cm) long and about 2/3" (16.7mm) in diameter.

Q: 4. Which Arca-Swiss camera plate will fit this?

A: This clamp accepts both traditional/regular arca-swiss plates as well as slidefix plates. Regular arca-swiss slides into the top dovetail whereas slidefix sits on the bottom dovetail. I've linked a few plates below, but for the regular plate all brands that use the arca-swiss compatible dovetail will work as long as their safety screws don't interfere. Regular: https://www.bhphotovideo.com/c/product/116072-REG/Arca_Swiss_802209_Universal_Camera_Plate_1_4.html?sts=pi&pim=Y https://www.bhphotovideo.com/c/product/822279-REG/Sirui_BSRTY50_TY50_Arca_Type_Pro_Quick.html Slidefix: https://www.bhphotovideo.com/c/product/663115-REG/Arca_Swiss_802283_Slidefix_100_QR_Camera.html

Q: 5. Is this arca swiss compatible?

A: Unfortunately Slik DQ-20 Compact Quick Release Adapter Set - Large is not arca swiss compatible.

Q: 6. Hello, I have bought from your shop the Arca-Swiss Monoball Z1 sp with Quick Release (B&H # ARZ1 ).However I would like to change the release clamp that I have with the Arca-Swiss Quickset FlipLock Round Quick Release Clamp (B&H # ARQR6038FL). Is that possible? Many thanks

A: hii don't believe you can change only the clamp, it doesn't work the ska way i think, you probably have to change the whole quick release

Q: 7. Does it fit into my Arca-Swiss d4 Tripod Head with a Classic Knob Quick Release? As I would like to change it to fliplock

A: The original quick release clamps on Arca-Swiss heads such as the D4 are attached without the intent to be user-interchangeable. There are reports of damaged clamp-attachment screws from those that have tried removing the clamps. We recommend leaving the original clamp attached.

Q: 8. I have many arca-Swiss mono ball fix camera plates. Can this I use this flip lock quickset device with the monoball plates? Also interchangeable with classic plates or has to be adjusted manually every Time?

A: The plates are interchangeable. They should be the same size, but I would always check to make sure they are snug before you let go of the camera equipment.

Q: 9. It doesnt appear the question about how to lock the legs was answered. How are they locked?

A: The legs do not lock but are stiff enough to hold their position given a the camera weight is not too much for the tripod load capacity.

Q: 10. How do the legs lock in two different height positions as advertised? Looking at the pictures I don’t see any height adjustable locking mechanism?

A: The legs don't telescope, it's just a matter of raising or lowering the angle of the legs.