The Key Digital 4K/18G HDMI over Single Cat 5e/6 Cable Extender Set with Power over CAT, HDMI Pass Thru, IR, RS-232 Provides fully automatic equalization to send video signals up to 406 x 2160 up to 328' over Cat6 cable.

Single CAT5e/6 UTP/STP Extension    Supports HDCP 2.2 and HDR10

• Single CAT5e/6 UTP/STP Extension:
  • Fully automatic equalization, and amplification depending on cabling length
• 4K Resolution Support:
  • 4096x2160 or 3840x2160 24/25/30/60hz at 4:4:4 (signals up to 18Gbps bandwidth)
• Flexible Power over CAT (PoC):
  • Only one power supply needed. Connect at Tx or Rx unit.
• Visually Lossless Compression:
  • 18G enabling technology applied to all video formats exceeding 10.2Gbps to accommodate transmission channel
• Low Profile:
  • Super slim chassis design
• Signal Extension: For resolution and cable quality
  • 4K/UHD (18G) with CAT5e/6: Up to 230'
  • 4K/UHD (18G) with CAT6A STP: Up to 328'
  • 1080p with CAT5e/6: Up to 230'
  • 1080p with CAT6A: Up to 328'
• 10G Pass-thru:
  • Mode enables uncompressed 10.2Gbps signal extension.
• HDR10 (High Dynamic Range):
  • More life-like images through a greater range of luminance levels
• HDCP 2.2:
  • Compliancy up to HDCP 2.x and backward compliant
• Deep Color Support:
  • Up to UHD/4K 30Hz 4:4:4/12 bits or 60Hz 4:4:4/8 bit
• IR Sensor:
  • Sensor powering via +5V on IR In ports collects line-of-sight IR from remote(s) without external IR connecting block
• Up/Down IR:
  • Two channels of IR enable control to/from devices or control systems connected to Tx and Rx units
• RS-232:
  • Bi-Directional control to/from Tx and Rx unit on Phoenix connector
• Full Buffer Technology:
  • Key Digital’s proprietary suite of EDID, HDCP, TMDS, and HPD management to overcome Pro AV installation obstacles
• EDID Management:
  • Internal library with 14 internal EDID handshakes including 4K with HDR in addition to native EDID data copied from CAT5e/6 or HDMI pass-thru outputs
• HDCP Authentication:
  • HDCP sources are authenticated by HDCP key on transmit unit, for one-to-one topology
• Hot Plug Detection Control:
  • Enables integrator to choose if active signal voltage is forced to connected display/output device
• TMDS Re-Clocking:
  • Re-generation of TMDS (AV signal) channel data at Transmit unit for brand new AV signal
• Surround Audio Support:
  • on HDMI pass-thru and UHDoTP outputs:
  • HDMI Pass-Thru: Supports Dolby DolbyTrueHD, DTS and DTS-HD (formats up to 7.1)
  • CAT5e/6 Output: Supports Dolby, DTS (formats up to 5.1/6.1)

Related Questions and Answers

Q: 1. Will this system support multiple receivers from one transmitter?

A: According to DVDO, the Transmitter is only able to transmit a Wireless Signal to the One Receiver it is packaged with. Unfortunately the Transmitter is not able to send Multiple wireless signals to Multiple Receivers.

Q: 2. How long is each of these ramps?

A: These are 40" long.

Q: 3. What is the material?

A: The Wooden Camera Dead Cat Windscreen is made of Acoustically Transparent Artificial Fur.

Q: 4. Is there any sort of a delay from transmit to receive? I used other brands as a way to extend a computer monitor and had horrible lag. What is the lag like with this device?

A: This has a very low latency.

Q: 5. Is it possible to buy this kit and another receiver, so I can transmit the signal (audio and vdeo) to 2 tv's at the same time?

A: To be able to do that, you would need to either split the signal at the source into 2 wireless systems, or split the signal coming out of the receiver into your displays.

Q: 6. Will this work as a device to stream capture from the Dishanywhere app in the web browser or using Capture4me app ?

A: This will not allow you to capture a Dish Network or any other cable/satellite feed.

Q: 7. Are the overall dimensions of the protector 39.8x4.9? If so, what are the dimensions of the "internal" channel?

A: The measurement for the channel of the Pyle Pro Drop-Over Cable Protector Ramp (4.9 x 39.8") is not published. The Maximum cable diameter for the channel is .5".

Q: 8. Can these boxes be powered with 6 Volt batteries, if a-c power is not available? (Runtimes can be approximated from the current capacities of the provided a-c power supplies.)

A: These transmitters/receivers are designed for 5V. It is best to stick within the power requirements of the product to avoid causing damage.

Q: 9. will 1/2" conduit go under it

A: The Pyle Pro Protective Cable & Wire Concealment Ramp Track (4.9 x 39.8") (B&H# PYPCBLCO19) allows for up to 1/2" outside diameter conduit or cable to fit underneath it.

Q: 10. What battery plate is shown in the pictures? And does it have a gold mount version?

A: The Tilta Power Pass-Through Plate for DJI RS 3/RS 3 Pro (No Battery Plate) does not come with a battery plate. Please review the Gold and V-Mount plates listed below: Tilta Power Pass-Through Plate with Gold Mount Battery Plate BH #TIGAPPK2AB Tilta Power Pass-Through Plate with V-Mount Battery Plate BH #TIGAPPK2V