The aluminum Rugged Articulating Magic Arm from ANDYCINE incorporates stainless steel ball joints that offer solid support for mounting an onboard monitor, a light, or another accessory on your camera rig. This versatile arm supports up to 3.3 lb, and its locking lever provides a solid, single-point locking mechanism for the three articulated joints. The ball heads at each end of the arm enable 360° rotation, and they feature 1/4"-20 screw mounts. The arm measures 7" from end to end when fully extended.

Attach Accessories to Camera Rig    Fully Extends up to 7"    1/4"-20 Screws on Either End    Supports Accessory up to 3.3 lb    360° Ball Head on Either End    360° Rotation on Center Joint    Aluminum & Steel Construction

Related Questions and Answers

Q: 1. Can I use this to mount the Marshall Electronics CV420-30X-IP Zoom Block UHD 4K IP Camera with HDMI 2.0 & PoE on a ceiling or on a wall?

A: It is physically possible. However we feel you might want to invest in a more robust solution for a camera. The Impact 2 Section Double Articulated Arm without Camera Bracket, BH #IMBHE117, with a larger clamp would be a better idea, BH #IMCC106R. https://bhpho.to/321jDyH https://bhpho.to/381HFNy

Q: 2. I have the SmallHD 701 lite, will this support the monitor?

A: This arm will support your monitor.. The only issue is that you will have to really tighten it. This arm tends to loosen randomly.

Q: 3. Do the pins compress to flat for none arri mounts?

A: Yes, the locating pins on the Tilta Tiltaing Mini Articulating Arm are retractable.

Q: 4. Will this mount to a moza lite 2 gimbal?

A: As the Atom Clamp has a jaw opening of about 1.3 , that should clamp to the top crossbar of the Moza. Both ends of the articulating arm have a standard 1/4=20 threaded stud on them, which can screw into tapped holes on a rig or other accessories like the Atom Clamp, coldshoe adapter, etc.Clamp this only to the top cross bar as clamping to any of the moving parts may throw off the balance enough that the servos won't be able to adequately compensate for it.

Q: 5. What size are the taps on the ends?

A: Both ends are 5/8" pins 1 end has a 1/4" x 20 threaded hole the other end is 3/8" x 16

Q: 6. Does the shoe mount side unscrew further to reveal another male thread? (aka two male threaded sides?) I would use this to clamp to my Ronin-M but I would need one male thread to go into the clamp and another male end to go into the monitor. (If not, can anyone recommend one). -thanks!

A: Yes

Q: 7. Will this work with a Sony A7iii and an Atomos Ninja V5?

A: yes, the articulating arm will support the payload of the display. But we always highly suggest a roll cage for extra stability.

Q: 8. How many pounds will this hold? Thanks.

A: Though not rated for weight load, this arm will work with products like 7 video monitors. So no more than 3 lbs.

Q: 9. Hi there, will this work with a Small HD Focus 5" monitor?

A: According to Andycine, the Andycine Tilt Arm for 4.5 to 5.7- Monitors, "works with ANDYCINE 4.5 to 5.7" monitors, and similar 3rd-party monitors with a 1/4"-20 threaded hole on the side." Since the SmallHD Focus 5" monitor is a 5" screen with a side 1/4"-20 mounting thread, it should work fine.

Q: 10. What is the distance from the side 1/4 20 connector to the bottom arm?

A: That spec is not listed as this arm is specifically for ANDYCINE Monitors between 4.5 to 5.7 inches. If you have an ANDYCINE monitor in that size range this will work.