Charge two V-mount batteries simultaneously with the IndiPRO Tools Dual V-Mount Intelligent Battery Charger. Its intelligent interface identifies the battery's capacity and selects the appropriate charging current. Batteries under 100Wh are charged at 3A and batteries over 160Wh at 6A. Any batteries that fall within the 100 to 160Wh range are charged at 4.5A.

An integrated LCD screen displays the charging status of each battery. Top vents ensure proper heat dissipation and prevent overheating. The charger has a compact form factor and a built-in carry handle for portability.

For V-Mount Batteries    Charge Two Batteries Simultaneously    Identifies Battery Capacity    LCD Screen Displays Status    Carry Handle, Top Vents

Related Questions and Answers

Q: 1. Will the charger stop delivering current to the batteries when they reach a fully charged condition? (to prevent overcharging or excess heat in the batteries)

A: Yes it will. This charger will not overcharge or cause the batteries to overheat.

Q: 2. Can I gang two IndiPro batteries (eg Micro series 98's) and power the LS120d-II via the d-tap on the it's controller?

A: Yes you can gang 2 Batteries to power a unit, but If you plan to do it by the D-tap on the battery, it has a 3 amp max output through the D-tap on the battery, But if you do it through a the D-tap on a plate "V mount or Gold mount plate" it would be fine

Q: 3. Would Core SWX HyperCore 150 Gold Mount Battery be able to be charged with this unit?

A: Yes, the IndiPRO Tools Quad Pro Battery Charger (Gold Mount) will charge the Core SWX Hypercore NEO 150 Mini 147Wh Lithium-Ion Battery (Gold Mount), BH #CONEO150AG.

Q: 4. Can I use my Switronix V-Mount batteries on this?

A: We have been reassured repeatedly that all V-mount and gold mount batteries have the same standards as to battery charging and chargers. However, proprietary features may or may not function such as with the display of power remaining. Also note: while highly unlikely there is to be a problem, warranties may not be honored. Proceed with that knowledge.

Q: 5. Will this charge the Switronix Hypercore Slim HC7S ?

A: In order that you get the best performance between battery and charger, we strongly recommend that you keep it all in the family. We therefore suggest for the HC7S that you get the Switronix GP-2LSJ 2-Position Simultaneous Charger. Please see attached. That being said, the HyperCore Slim V-Mount will charge on Sony, IDX, and Switronix V-Mount chargers, and chances are very good it will be fine on the IndiPRO. However, this combination has not been tested by Switronix therefore performance cannot be verified nor guaranteed at this time.

Q: 6. Will this charger work with Anton Baur batteries, or do I have to spend $1000 more?

A: You will need an Anton Bauer charger. AB batteries will only charge on AB chargers.

Q: 7. Around how long will it charge 4pcs of SWIT S-8110S 126Wh V-Mount Battery? Thanks!

A: Battery run and charge times are so situation dependent, manufacturer's are unable to post this seemingly obvious information. In the process of determining the time the process takes, consideration must be made regarding the size of the battery, how depleted it is and then multiply by how many batteries need to be charged. The best answer we can give is an guesstimate of 2-4-6 hours.

Q: 8. Can you power stuff through the v-mount? Or just the dc output.

A: There are 2 different ways to power with this unit. You can power directly from the V-Mount connection from the back of the plate or through the 2.5mm output jack that is located on the side. You will just need the 2.5mm connector cable to power your specific device/camera.

Q: 9. Does the charger stop charging when the battery is completely charged?

A: The IndiPRO Tools Quad Pro Battery Charger (V-Mount) does have an auto sense feature built in that will stop sending power to a batter once it has been fully charged.

Q: 10. Hi there! Can I charge TITON 150 batteries? Thank you!

A: Unfortunately any Anton Bauer Batteries will not work with any of our chargers.