The Hensel Light Stand Kit features two black-anodized, three-section stands. Each stand can support loads up to 19.8 lb, rises to a maximum height of 9.1', and comes in a padded storage bag. A valuable asset is the stand's pneumatic air cushioning, which gently lowers your fixture when making height adjustments, avoiding damage to expensive equipment. The stands accept optional wheels for smooth repositioning without lowering the gear to a minimum height.

2 Air-Cushioned Light Stands    9.1' Max Height    3 Sections    Includes Storage Bag

Related Questions and Answers

Q: 1. where can i buy spare parts?

A: You would have to either use the link below (http://bit.ly/1SRMuK5) or contact Litepanels directly if you need replacement for your needs. You may contact Litepanels either by calling (877) 412-7467 or by sending an e-mail to support@a href= http://shopatron.com target= _blank shopatron.com./a

Q: 2. Would this fit three 43 light stands?

A: Yes, It's about 47 long and has enough volume for around four medium sized light stands. The materials, padding and craftsmanship are top notch but the design is not. I measured it to be sure and found the holding straps are stitched to the bag slightly off center by one inch. They are stitched to the bag too close together too so the bag see-saws toward one end and the light stands inside slide to one end and the bag becomes not level with the ground as you walk and is uncomfortable to hold. Also, this bag does not come with a shoulder strap. I will never buy a tripod/light stand bag without a shoulder strap. Going down to the beach is a real hassle without one.

Q: 3. Does this stand hold ring lights?

A: This stand has a standard 5/8 post at the top like the vast majority of light stands I've used, so if your ring light has normal stand mounting hardware it should work fine. If your light doesn't have the most common mounting hardware, adapters and clamps are available.

Q: 4. I'm a little reluctant to purchase this because it's not air cushioned. I tend to be clumsy at times. I don't want it to come slamming down and break my flash. Anyone have any scares with this one?

A: I found this to not only be a great buy but stable and sturdy. I use battery powered LED lights and it is perfect.

Q: 5. Is the 1/4 " thread on this stand compatible with the iPad teleprompter? And can it also handle the weight?

A: The I Pad teleprompter will fit on the ¼ -20 threads of the Impact Light Stand, Black (6') However, please note that the rated load capacity of the light stand is 4 lb.

Q: 6. I have this stand, it has a loose joint. Basically the screw tighten on the top joint is tight, but the pole still slides out and rotates as though it hasn't been tightened. There is a problem inside at that joint, maybe a sleeve is missing or something. Has anyone encountered this problem? Know how to repair it? Looking for a diy solution, not sending it in for repair.Can you help me with this? Id like to attempt a repair myself.Thank you,Andy

A: Sorry I haven't had this problem

Q: 7. What materials is this stand made from, especially in a tightening areas?

A: Main shaft, legs & struts are anodized aluminum extrusions. Pivots are heavy duty steel rivets. Main shaft clamps are of a thick cast plastic with steel threaded bolts capped with plastic. The central base plate is also relatively think plastic component. Overall, a well made lightweight stand & good value for light to medium usage, however it's not likely to hold up for a Pro that require steady daily use requiring frequent broken down & transport. Hope this helps.

Q: 8. Package weight says 4.0 lbs. How much does the actual stand weigh?

A: about 2 lbs.

Q: 9. how long is the stand when it is collapsed?

A: 26.3 inches

Q: 10. Does the shutter speed reading change in one-third increments? for instance, can a flash reading be achieved at 1/320 second or does the shutter speed selection only read in full stops like 1/125, 1/250, 1/500?

A: This light meter goes in 1/10th increments.