Designed for use with 100mm bowl tripods, the Acebil CH7(F) Fluid Head features a 100mm ball design and supports loads up to 33 lb. An 8-step counterbalance allows you to compensate for the weight of your rig for better balancing, while independent 6-step pan and tilt drag settings provide adjustable resistance for precise movements. A sliding quick release plate attaches to your camera via a 1/4"-20 or 3/8"-16 screw, for easy attachment and removal. To assist in keeping your shots level, even in dim environments, the head has a built-in LED illuminated bubble level. A pan bar comes included and can be attached on either the left or right side of the head.

2-Stage T1002CG Carbon Fiber Tripod    CH7(F) Fluid Head, 33 lb Load Capacity    100mm Bowl, Ground Spreader    Includes Carry Bag

• Supports loads up to 33 lb
• 100mm ball
• 8-Step counterbalance
• Independent 6-step pan and tilt drag settings
• Tilt range: +90° / -70°
• Built-in LED illuminated bubble level
• Sliding quick release plate with 1/4"-20 and 3/8"-16 screws
• Included pan bar can be attached on left or right side of head

Related Questions and Answers

Q: 1. is there another spreader I could use with this tripod to go lower, other than the one included?

A: There is a floor spreader model as well as this mid-level one seen here. Acebil T1002G Tripod Legs (100mm Bowl) B&H # ACT1002G. However, to get as low as possible with this tripod, you would have to remove whatever spreader it has. The lowest possible set up would come with a smaller tripod or a hi-hat. E-Image Hi-Hat with 75/100mm Bowl B&H # EI7500 is one possibility.

Q: 2. Where can I find a replacement plate-locking lever for the 3/8 screw?

A: For Miliboo tripod service parts the best contact is the following - https://bit.ly/3y2paES

Q: 3. What is the closed length?

A: The Libec RT20C 2-Stage Lightweight Carbon Fiber Tripod with 75mm Bowl (B&H# LIRT20C) is 26.4 inches (67cm) long when folded.

Q: 4. can the spreader be removed? would that affect the stability?

A: Yes removing the ground spreader would effect stability. You could add a Mid-Level spreader. Also you could choose the Mid-level model of this tripod for additional stability. Mid-level Tripod Kit - https://bhpho.to/3Ibs0xk Mid-Level spreader - https://bhpho.to/3FZF5Hx

Q: 5. What is the load capacity of the legs alone? In case I want to mount a slider with a camera.

A: Not more than 8 pounds and that is pushing it. Of course you know that sliders are best when secured at both ends or on solid ground...unless it is a very short slider.

Q: 6. How do you place the tripod feet into the ground tripod spreader?

A: Depende que tipo de tripode, pero deberias ponerlo en modo de que la goma entre a la pata del tripode

Q: 7. Min height is 25" or 17"? It says both. Then again for some reason the Carbon version says its 17" too.

A: The height range of this tripod is 25.2 to 58.3 inches.

Q: 8. How tall is it and how does it weigh?

A: Sorry, but this tripod and battery selection is no longer available. The tripod and head are still available. See below.The maximum height is 62.2 (158cm). The combined weigh 10.6 lbs (4.8kg).

Q: 9. is it delivered with its transport's bag?

A: yes, the bag is included in the system

Q: 10. Does this accesory works wiht 501hd tripod?

A: That will depend on the legs you are using with the 501HD Head. This tripod works with Manfrotto legs that have spiked feet and are between 31" to 51" in leg spread.