This 2-pack of natural walnut 106.3 x 23.4 x 0.47" Vicoustic VicStrip is a new innovative approach to slat panels by introducing Laminated VicPET Wool, which is free of wood, making it more sustainable, flexible, and lightweight. The VicStrip was drawn with the lines of contemporary styling decorative wall panels, for anyone that wishes to provide offices, restaurants, hotels, and homes with a design-embellished solution with the added value of removing sound reverberation.

Wall and Ceiling Acoustic Slat Panel

• Lightweight, making it easy to transport and apply, offering a less expensive shipment
• Easy to cut and readjust to the room’s requirements
• Can be glued or screwed to walls and ceilings
• Free of wood, metal, and nails, and with joints almost invisible
• Sustainable by being manufactured with VicPET Wool, a material produced mainly from recycled plastic bottles
• Low-emission material for good air quality, meeting the human-ecological requirements established for babies, without irritating skin or eyes
• A green product suitable for green projects certification
• Sound absorption properties to control medium and high frequencies, engineered at Vicoustic research lab for VicPET Wool
• Humidity resistant with no dust generation during handling
• Washable and easy to clean, simply by using a sponge and water
• Fits perfectly with the rest of the Vicoustic product range

Related Questions and Answers

Q: 1. 1. What is the life of the LED light? 2. Do they require calibration? 3. How often should they be replaced? Or Calibrated if they can be calibrated?

A: The LEDs in the Genaray SpectroLED 800 Bi-Color Studio LED 2-Light Kit are rated for 50,000 hours (the equivalent of running the light fixture for 8 hours every day for approximately 17 years). The light fixture should not require calibration. In the event you have an issue with the light fixture, you would contact Genaray directly, as there are no user-serviceable parts in the Genaray SpectroLED 800 Bi-Color Studio LED 2-Light Kit. I would recommend replacing the light fixtures either when they become inoperable or when you decide you need a new light fixture.

Q: 2. What type of finish is on the cabinet?

A: Red Walnut Veneer

Q: 3. Will this work with any light stand?

A: This is just a reinforcement for seamless paper. It has nothing to do with light stands. It will work well with varidrive background support systems. You could technically use it with background support systems that use a cross pole, but it will be loose and harder to control.

Q: 4. What is the diameter of these pipes, please?

A: Measured with calipers, O.D. is 1.970 to 1.975 and I.D. is 1.85

Q: 5. Did anyone else have an issue with the pole not being wide enough in diameter? I'm unable to fit my Drive sets into it making it really hard to use!

A: This is compatible with the Impact Vari-drive and the Manfrotto Expan drive. If you are using a different brand, it may not be compatible.

Q: 6. How do I attach a vinyl seamless to the pole? Tape?

A: That's what I did. I used some acid-free clear packing tape, but gaffer tape might be better. Definitely not duct-tape.

Q: 7. What power supply would this work with 220v or 110v?

A: Each of the LED panels of the Genaray Spectro LED 800B1 Bi-Color LED Light Panel (3-Light Kit with Softboxes and Case) (B&H# GESPS800B13B) comes with an AC transformer that accepts 100-240VAC. So, it will work at both 220VAC and 110VAC.

Q: 8. Is anyone using this to hang 53" seamless? I'm assuming it would require using only one of the poles? If that is the case can each part of the pole be used for two separate 53" seamless paper rolls?

A: This crosspole can be used to replaced the cardboard core on a 53" seamless, so you can use a set of Impact Varidrives to bring the roll up or down as needed. If you were using two 53" rolls, it may be difficult to connect the two sections since one section fits completely flush to the roll.

Q: 9. What cable(s) can I use to connect my Nord C2D to this speaker? Besides the expensive 11-pin cable...

A: The 11-pin cable seems ideal for connecting your Nord C2D to the Hammond 3300 Leslie Rotary Portable Speaker (Red Walnut), however as an alternative you could connect the L/R 1/4" outputs of your Nord to the 1/4" line input of the Hammond. A cable such as BH #MOSRC1421412 Mogami 1/4" TRS to Dual 1/4" TS Gold Send/Return Cable (12') would be appropriate.

Q: 10. where is the power switch for the leslie?

A: In back on the bottom where the speed control and everything else is.