Use the 1/4"-20 Counterweight Clamp from DigitalFoto Solution to balance a heavier camera rig on your handheld gimbal stabilizer. This aluminum counterweight holder uses a clamp with a 0.6" range to mount on the side arm of your handheld gimbal. The seven 1/4"-20 threads are distributed on four sides to enable more precise balancing. Rubber padding inside the clamp helps to prevent scratching your gimbal.

Use to Balance Camera on Gimbal    7 x 1/4"-20 Counterweight Threads    Compatible with Most Handheld Gimbals    0.6" Clamp Range    Mounts on Gimbal Side Arm    Rubber Padding Prevents Scratches

Related Questions and Answers

Q: 1. if my zhiyun cran 3s pro plus fs7 weights around 8 to 9 kg, can it handle it?

A: Yes, the THANOS-PRO II can support up to 10.5 kg.

Q: 2. Does the weight of the Thanos-Pro rig rest comfortably on the HIPS, or, does it create lower back pain/fatigue while using (as a few users apparently experienced with the Tilta Float system)? Thanks!

A: The Thanos Pro II helps reduce stress from your arms and shoulders while using it and transfer that weight to the hips, along with your back. there are always measures you can take to make the rig more comfortable in terms of fatigue, at the end of the day after hours of use it is taxing and fatiguing.

Q: 3. Where can I get the grid that fits this unit?

A: The DigitalFoto Solution Limited V360QB-3 Background Frame with Removable Diffuser is 39 x 39" it would accept a 40x40" grid from impact. Impact Fabric Grid for Large Square Luxbanx (40 x 40") B&H # IMLBGSQL

Q: 4. is it compatible with the canon r3?

A: Yes, the DigitalFoto Solution Limited THANOS-PRO II Gimbal Support System (B&H# DITHANOSPRO2) can support the Canon EOS R3 body. Please keep in mind that the maximum supported gimbal weight is 23 lb / 10.5 kg. Also, you'll be using the internal battery of the R3 since the included dummy batteries are not designed for the R3. Alternatively, you could chose a different dummy battery (not sold by DigitalFoto) that would suit your setup.

Q: 5. Does this come with the Trini-slider?

A: Please see the In the box listing for the included accessories, for the DigitalFoto Solution Limited THANOS-PRO II Gimbal Support System. We are not aware of a "Trini-slider" offered in this bundle. However, there is a "Slide Bracket for Sled", that is included.

Q: 6. Does this have the upgraded yoke system that was recently released on the DigitalFoto site?

A: Yes, this will start shipping with the modification.

Q: 7. Would this work on a Zhiyun Crane 3 with a Sony A7R iii?

A: It is our opinion that the DigitalFoto Solution Limited R180 L-Shaped Vertical Clapper Bracket (7.1") is too tall and too heavy to balance on the Zhiyun CRANE 3 LAB Handheld Stabilizer.

Q: 8. Will this work with a Sony FX9 camera and a manfrotto camera plate attached to the tripod?

A: The DigitalFoto Solution Limited R180 L-Shaped Vertical Clapper Bracket (7.1") should be able to support the Sony PXW-FX9 XDCAM 6K Full-Frame Camera System (B&H # SOPXWFX9) and a Manfrotto quick release plate on a tripod.

Q: 9. Is this built for heavy duty rigs? I have a FS7 with Sigma Art 85mm, EVF, v-mount battery, shoulder mount and audio transmitter.

A: Yes, the DigitalFoto Solution Limited R180 L-Shaped Vertical Clapper Bracket (7.1") is built for heavy duty rigs and it will hold a Sony FS7 with Sigma Art 85mm, EVF, V-mount battery, shoulder mount, and an audio transmitter.

Q: 10. This plate seems quite skinny. Will this hold a FS7 with Sigma Art 85mm lens, EVF, v-mount battery, and audio transmitter?

A: The DigitalFoto Solution Limited R180 L-Shaped Vertical Clapper Bracket (7.1") is well made and has a load Capacity of 46.3 lb. It will hold a Sony FS7 with Sigma Art 85mm lens, EVF, V-mount battery, and an audio transmitter.