The Lectrosonics SNA600a Adjustable Dipole Antenna can be used with wireless microphone receivers or IFB transmitters. The antenna has a 100MHz bandwidth with a tunable center frequency between 550 and 800MHz. It can connect to your receiver or transmitter via its 50 ohm BNC connector and includes a 3/8" x 16 threaded socket and stud with a mounting strip for securing it to your equipment. The SNA600a itself is constructed of fiberglass circuit board material, can be folded for storage, and can be powered with antenna power enabled on your receiver or multicoupler.

For Wireless Receivers, IFB Transmitters    100MHz Bandwidth    Tunable Center Frequency    SWR Less Than 2:1 over 100MHz Bandwidth    50 Ohm BNC Connector    Foldable for Storage    3/8" x 16 Threaded Socket    Includes Mounting Strap

Related Questions and Answers

Q: 1. Can I use IFBT4's with this unit? They transmit at 250mW. Wondering if this can attenuate or handle that kind of power.

A: The Lectrosonics M2C accepts a maximum input of 100 mW per port, so no, they would not be recommended for use together.

Q: 2. I have an Sennheiser EW100 G3 Receiver with a frequency range of 516-558MHz. Will this antenna still work?

A: Yes, the Sennheiser HALF WAVE DIPOLE Half-Wave Antenna Rods for EW-D EM Receiver are compatible for use with the Sennheiser EM 100 G3 Wireless Receiver that operates on the 516 to 558 MHz frequency band.

Q: 3. Sorry for the question, but this doesn't look like it has a 2.5mm screw in termination, but it says it's compatible with the UM190. This screw in termination will still work? Just want to make sure before I order it.

A: For the older model UM190 without the SMA screw on antenna connection the Remote Audio ANL5 is an alternative.

Q: 4. Can I use these with an antenna distribution system, instead of the shark fin style? So 4 receivers would be patched into 1 of these antennas...

A: An antenna of this type would not be recommended for a distribution unit. They are designed to be used as a pair with a single receiver, and will not work properly connected to an antenna distro carrying multiple signals.

Q: 5. are these antenna compatible with the XSW Band A iem?

A: The Sennheiser HALF WAVE DIPOLE Half-Wave Antenna Rods for EW-D EM Receiver are not intended for use with an IEM transmitter.

Q: 6. Is it okay to keep it in the rain or should the antenna be covered with a plastic bag?

A: The Lectrosonics ALP620 Perforated LPDA Shark Fin Style Antenna is not IP-rated; therefore, it cannot be left out in the rain. Using a plastic bag or rain cover to protect it will actually affect the wireless range of the antenna, making it prone to RF interference.

Q: 7. what is the length or dimension of the antenna?

A: The Sennheiser HALF WAVE DIPOLE Half-Wave Antenna Rods for EW-D EM Receiver are 13.5" (344mm) long.

Q: 8. can I get it for block 25?

A: Yes. B&H # LEAMJ25 is the Lectrosonics AMJ Color Coded Whip Antenna for Lectrosonics Belt Packs that is for Block 25. We do currently have it available in stock. http://www.bhphotovideo.com/c/product/823689-REG/Lectrosonics_AMJ25_AMJ_Color_Coded_Whip.html

Q: 9. are These antennas compatible with Sennheiser G4 EW100 Receivers?

A: Yes, the Sennheiser HALF WAVE DIPOLE Half-Wave Antenna Rods for EW-D EM Receiver are also compatible with EW100 G4 receivers operating within the 470 to 550 MHz frequency range.

Q: 10. Can I plug this directly into an SMV transmitter that's set to IFB mode and get a better signal?

A: Yes, in theory the Lectrosonics SNA600a Adjustable Dipole Antenna's BNC connection could be adapted to the "SMA" type antenna connection on a Lectrosonics SMv transmitter to widen the transmitters output signal.