Sennheiser Headphones Cx 300S

Telex Wp-300s Wall Plate Microphone With Switch

Product Code: ga1352
Availability: In Stock

$330.00 $481.80

Qty

11 reviews Write a review

Description
Reviews (11)

The Telex WP-300S is a dynamic wall plate microphone that installs into a standard electrical, single gang wall box. The WP-300S features a dynamic element that's specifically designed to reproduce speech with enhanced detail and intelligibility. In addition, the double-pole, double-throw switch enables push-to-talk and line shorting capabilities. The WP-300S is ideal for security applications, drive through installation and more.

Microphone
Polar Pattern	Omnidirectional
Element Type	Dynamic
Performance
Frequency Response	100 Hz to 10 kHz
Connectivity
Analog Output	1x Pigtail/Unterminated
Physical
Color	Silver
Dimensions	H: 4.5 x W: 2.75 x L: 1.12" / H: 114.3 x W: 69.85 x L: 28.58 mm
Weight	3 oz / 8.5 g
Packaging Info
Package Weight	0.35 lb
Box Dimensions (LxWxH)	6.05 x 4.6 x 3.7"

The double-pole, double-throw switch enables push-to-talk and line shorting capabilities.

The WP-300S features a dynamic element that handles high peak response without distortion.

The omnidirectional polar pattern provides an even pick at the direct and off-axis sections of the microphone.

The WP-300S installs into a standard electrical, single gang wall box.

Related Questions and Answers

Q: 1. Is the pin removable?

A: The pin is welded in place.

Q: 2. What is the distance between the bigger holes on the short end?

A: From the center of each hole, we measured 65mm with a vernier caliper.

Q: 3. what is the distance between the holes?

A: The large Outside holes are 6 centimeters by 13 centimeters on center. The small Inner holes are 4 centimeters by 12 centimeters on center.

Q: 4. How big are the holes and what' the spacing? Was thinking of putting some magnets on this and want to get some ideas on sizes

A: The larger holes are 5mm, and the smaller 3mm. From center to center the large holes are 5.5 cm apart. From center to center the small holes are 3.5 cm apart. The entire plate is approximately 7.5cm x 14.5cm

Q: 5. Will this mic work with 4 pin ham/CB radios

A: In theory, if wired with the proper connection attached, the Telex 450D Dynamic Push-to-Talk Handheld Paging Microphone could work with CB radios. The 450D comes with an unterminated cable connection meant primarily for for direct integration with commercial PA amplifier systems.

Q: 6. What size diameter is the holes or anchor points? I want to secure Kino clips onto them.

A: Think it is 1/4 inch and 1/8 inch for smaller

Q: 7. Which hole is the "safety cable hole"?

A: safety cable goes on the Baby Pin

Q: 8. Can this be mounted on a standard light stand?

A: This Impact Wall Plate can only mount to a wall or ceiling and would accept a junior pin on top.

Q: 9. Will this work with any intercom system?

A: It will not work with any system. The Telex MCP90 is a gooseneck electret condenser microphone, designed for front panel connection to that company's RTS system and select Audiocom intercom stations.

Q: 10. Is this compatible with the Matthews BabySitt'r?

A: This is a Baby 5/8 pin it's compatible with any Baby pin accessory.

Michael	08/09/2024
This product works GREAT! This was a relatively short run (30') so Cat 5e worked just fine. Both devices powered from one end (Input TX) with this install. They were available, affordable and easy to install. The Power Supply is an inline DC supply, not a plug-in wall wart. This has been my go to HDMI extender kit. Kramer devices always work. 5

Mati	01/09/2024
nice 5

John	29/06/2024
It came quicker than I expected and works great. Nice and easy to install and use. 5

Miaobo	21/06/2024
fast delivery. Packaged well. 5

Dre	16/06/2024
I've used these many times and they worked amazing! 5

Jim	06/06/2024
This works perfectly and is very handy to have. Very strong and well made. This can be mounted anywhere that you can screw or nail into, like a wall, ceiling, board, floor or apple box. I'm currently using mine attached to an apple box so that I can mount lights down low and it's working great. Comes with a 1-1/8 receiver so it will hold any thing that has a male 1-1/8 pin. I plan on getting a junior to baby pin adapter so I can attach normal lights with a 1 x 5/8 Receiver (Via Yoke Mount) easily. And the 1-1/8 receiver can hold c-stand column too. You can even attach the 1-1/8 receiver to a stand upside down, so you have a flat base on top for a monitor or speaker or anything else, or screw in a pancake apple box for an even larger flat surface. The build quality is fantastic. It is made of steel and very solid. The knob is also metal and super strong and tightens down very securely. This can hold a lot of weight. And the 8 holes on the plate allows you to add a bunch of screws or nails to where ever you attach it, giving you even more peace of mind that it's secure. This is a great addition to my production grip gear and has a variety of uses. I'm very impressed with the build quality and functionality. [I have received this product in exchange for my honest review] 5

Steven	06/05/2024
Looks pretty comparable to the Kupo and other junior wall plates. Solid. 5

Joao Luiz	25/04/2024
Solid 5

Jennifer	16/04/2024
We ordered to replace a batch of 10 yr old microphones that no longer worked and the new ones work great! No issues. Shipping was fast and they arrived just in time for a big event! 5

Panagiotis	08/04/2024
I have many of these installed in restaurants, paired with an audioengine B1 bluetooth transmitter and the sound quality is excellent. Being able to transmit an RCA signal over long distances with UTP cable in a single gang decora device that doesnt require power is really amazing. My only complaint is that its very difficult to get two of these side by side in a two gang mud ring/low voltage box. You have to grind the mud ring down and grind the plastic corners of the baluns to make it work. Please muxlab never stop making these! 5