The lime, waterproof 904 Hard Case without Foam from Nanuk is a small crushproof hard case made from lightweight NK-7 resin that protects and stores compact gear, such as a mirrorless camera and lens or a two-way radio with accessories. To protect your gear within the case, an optional multi-layered cubed foam insert is available with pre-scored squares that can be individually removed to accommodate the shape of your gear.

The dustproof case secures with the Powerclaw latching system, which includes a patented Powerclaw latch that uses compressive force to tightly clamp the case shut, plus an integrated slide lock that prevents the case from opening during transport or when dropped. For additional security, there are hasps for adding optional 900 Series Nanuk padlocks or a tie lock when traveling.

The case features stainless steel hardware and can be carried using a foldable soft-grip handle at the top. The handle structure is molded with the NK-7 resin and is covered with soft shock-absorbing rubber for comfort in carrying heavy loads. Integrated stays in the handle keep it folded down, avoiding damage during transport or shipping.

Holds Mirrorless Camera or Two-Way Radio    Waterproof, Crushproof, and Lightweight    Powerclaw Latching System    Automatic Pressure-Release Valve    Molded-In Bezel System    Integrated Lid Stay for Easy Access    Stackable with Same-Size Cases    Padlockable and Dustproof    Foldable Soft-Grip Handle

Automatic pressure valve guards against the vacuum caused by changes in altitude and geographic location that tend to seal watertight cases shut.

Pressure valve equalizes atmospheric pressure using micro vents, which allow air to pass through, but prevent water from getting inside.

Waterproof, custom-fit gasket, or seal, is made from high-quality EPDM rubber and resists deformation and fatigue.

NK-7 resin is UV-resistant to protect against discoloration and material degradation.

Molded-in bezel system includes detailing on the lower portion of the case for installing a panel kit without using a secondary bracket or drilling holes in the side of the case.

Bezel system accommodates an optional Waterproof Case Panel Kit or mounted electronic, measurement, or test equipment to use the case as an independent mobile test or control unit.

Integrated lid stay prevents the lid from closing while you access your gear.

Grooves on the front interlock with built-in feet at the base when stacking multiple cases of the same size, which saves space for transport.

Related Questions and Answers

Q: 1. Will this case fit a Sony A7Sii?

A: Hi, yes, this case can be used for an A7s II.

Q: 2. Would this box fit a Sony FX6 and FE 24-105mm f/4 G OSS Lens?

A: No. Following unit is designed and made for the Sony a7R system.

Q: 3. would this case hold larger camera bodies and lens if I lay the bodies down flat along with the lens?

A: I think so, but not many of the larger bodies/lenses will fit. I have a Fuji XT1 and three lenses, plus filters, 5 spare batteries, and various other bits, and they all fit fine. I got the padded inserts rather than the foam. I highly recommend this case, or a bit larger one from Nanuk. It's a pleasure to use.

Q: 4. Does this case fit the Nikon D800 body?

A: Yes, this case would fit the Nikon D800 body.

Q: 5. Will this fit the canon r10 with the 18-150 mm lens and the canon f1.8 18mm macro lens?

A: Unfortunately, the Nanuk 904 Case with Foam would be too small for the Canon EOS R10 with the RF 18-150mm attached and an additional lens. A more suitable case is the Pelican Vault V300 Large Case with Lid Foam and Dividers (Black), BH # PEV300LLDB. https://bhpho.to/3UtzzlH

Q: 6. Will the Nikon Z6 with the native 50mm fit in this case?

A: It would be too small. Pelican makes one that would work https://bhpho.to/2JHFJxv.

Q: 7. Is the foam cubed that I need to cut out or is the foam cutout the way it shows in the picture?

A: The foam is pre-cut into the configuration shown in the images. For the standard cubed foam configuration, please see https://bhpho.to/363A8N4

Q: 8. Will the controller section hold a DJI Smart Controller?

A: The Nanuk 910 Case with Custom Foam for DJI Mini 2 Fly More Combo (Lime) will not have a section for the DJI smart controller.

Q: 9. Can the FOAM be custom shaped / cut to fit a SONY PMW-300K1?

A: Yes, the foam is "scored" like pick and pluck type so you can pull it apart neatly to fit the camera shape and other devices.

Q: 10. is the foam pre cut or uncut?

A: The foam in the Nanuk 905 Hard Case for Sennheiser Single XS Wireless Set (Black, 6.3L) is pre-cut, with custom-cut slots for a receiver, a handheld microphone, a transmitter, a charging cable, and accessories.