The QSC RMX5050A 5000W Professional Power Amplifier is a 3RU unit designed for high powered live sound reinforcement applications. The amplifier can operate in stereo, dual mono, or mono bridged modes and can handle output impedances between 2 and 8 ohms. The unit is rated at 1100W per channel at 8 ohms between 20 and 20,000 Hz, 1800W per channel at 4 ohms between 20 and 20,000 Hz, 2500W per channel at 2 ohms between 20 and 20,000 Hz, and 3600W at 8 ohms in bridged mono mode between 20 and 20,000 Hz. The amplifier utilizes high-current toroidal transformers for greater power and lower noise when driving 2 ohms loads.

For I/O, the unit accepts balanced 1/4" TRS, XLR, and barrier strip inputs as well as touch proof binding post and Neutrik Speakon outputs. The front panel features independent gain controls for both channels with LED indicator lights to monitor the presence of the signal and when the signal is clipping.

Each channel is built with DC and thermal overload protection. Independent user-defeatable clip limiters reduce distortion. A selectable 30 or 50 Hz low-frequency filter can be engaged to protect your speakers from bottoming out and increase overall headroom.

3600W at 8 Ohms Bridged in 3RU Spaces    2500W per Channel at 2 Ohms Load    Balanced 1/4", XLR, Barrier Strip Inputs    Touch-Proof Binding Post Outputs    Professional Neutrik Speakon Outputs    Selectable Low-Frequency Filters    LED Signal and Clip Indicator Lights    User-Defeatable Clip Limiters    Dual Mono High-Current Power Supply    DC and Thermal Overload Protection

Related Questions and Answers

Q: 1. How can I connect 6 speakers to a 2 channel amp?

A: Depending on the specifications of your speakers it may not be possible to connect 6 speakers to a 2 channel amplifier. This particular amp is not designed to accept less than a 4 ohm load per channel. For information or suggestions on connecting speakers to this amplifier, please contact a Pro Audio Representative here by phone at 800-606-6969 or email audio@a href= http://bandh.com target= _blank bandh.com/a

Q: 2. Can this device be control by software, an API or Web Browser or Serial Port?

A: The Pyle Pro 20-Outlet 3600W 2 RU Rackmount Power Conditioner does not have any network control features.

Q: 3. hello it can be connected to a voltage 220?

A: The QSC GX3 operates at 120V AC. You will need to use a step-down transformer to use it with 220V AC such as the Sevenstar ST-500 Step Up/Step Down Transformer - 500W (B&H # SEST500UD) or Watson Voltage Converter - 500 Watt Max (B&H # WAVCGSD500).

Q: 4. how many speakers can I connect per channel?

A: The QSC GX3 features 2 physical speaker outputs designed for optimal operation at 8 ohms. The unit is able to operate safely with a 4 ohm load as well which will give you a higher wattage output per channel. You are able to connect multiple speakers to each channel in parallel, but should be careful not to exceed the wattage and impedance ratings listed by the manufacturer.

Q: 5. Can two amps be joined together to fit in a 1RU rack space with the included hardware?

A: Yes, two of the QSC SPA2-60 2-Channel Power Amplifier (60W) can be mounted side by side in one rack space. Installation instructions for this configuration can be found in the installation guide here: https://bhpho.to/4aKF5J4

Q: 6. It works with 4 and 8 ohm. What about 6 ohm?

A: The Pyle Pro PTA1000 is able to run at either 4 ohms or 8 ohms, but not 6 ohms.

Q: 7. Is it possible to output low impedance on channel one and high impedance on channel two simultaneously?

A: When in stereo mode, the QSC ISA300Ti Commercial Power Amplifier with 70V Transformer operates both outputs independently, so you could use one channel for 8Ohm and the other channel for 70V.

Q: 8. Is it better to used for lows bass or mids and highs?

A: Frequency Response 20Hz - 20kHz, +0, -1 dB

Q: 9. I need a 220V version of this amplifier. Could you possibly tell me the part number for the 220V?

A: The MFR# for the 220V version RCF IPS 700 600W Class AB Professional Power Amplifier is MFR# 12135087.

Q: 10. Im frm Philippines.. What is the right wattage/amperes of transformer be use to power this Gx3

A: You would need a step down transformer such as this BH #SEST1500UD.