Use this 9.8' Waterbird Power/Data Cable to deliver both power and communication to your compatible slider system. The cable features a female 4-pin XLR connector on one end and a male 4-pin XLR connector on the other. It can connect to Waterbird MS PRO, Swift, and XL slider systems to facilitate the exchange of power and control.

Delivers Power and Data    For Select MS Series Slider Systems    Female 4-Pin XLR to Male 4-Pin XLR    9.8' Total Length

Related Questions and Answers

Q: 1. Is this the correct cable to connect a Canon 6D to the Vello FreeWave Plus II receiver?

A: Yes, The Vello 2.5mm Remote Shutter Release Cable II for Canon 3-Pin Camera will work with the Vello FreeWave.

Q: 2. what is the length from the end of the Canon 3-pin connector to where the cable begins to coil?

A: From the end of the 3-pin connection to the start of the coil, the length of cable measures approximately 4" / 10cm.

Q: 3. Hi , will this work with Canon R5 . Thanks

A: Yes, this Vello 2.5mm remote shutter release cable for Canon 3-pin cameras is compatible with the Canon EOS R5.

Q: 4. What brand are the connectors on this cable? I have a cable that comes from Rode for my nt4 and it has black, no-name connectors, that seem to want to pull apart when you remove it from the mic. Concerning.

A: Rode has not specified a brand name for the XLR connectors. For another cable option with 5-pin XLR female to two 3-pin XLR male, you may want to consider the Remote Audio 5-Pin Stereo XLR Female to Dual XLR Male Y-Cable (B&H #RECAXSTE25) which is 25' long and uses Neutrik connectors with Mogami cable. The same Remote Audio cable is also available in 18" length (B&H #RECAXSTE). We also have the Sony 5-Pin to Dual 3-pin XLR Cable for ECM-680S (B&H #SO5P3PXSGC) which is 16" long and shows Neutrik connectors in the photo.

Q: 5. Will this work with the RS2 Pro and RS3 Pro too?

A: The Waterbird Slidekamera DJI Ronin Stabilizer Adapter would only support the DJI Professional Gimbal models like the DJI RS2, and DJI RS3 Pro.

Q: 6. is this the cable I would need for my canon 60D?

A: No. The Canon 60D uses the sub-mini connection. The appropriate cable you need is here: https://bhpho.to/3ss6P1x

Q: 7. What is the power rating on the output of this device? (watts or amps)

A: The power rating depends on the battery it is hooked up to. The P-Tap batteries that we sell seem to top out around 266 Wh.

Q: 8. Some of the original mini cables that came from Rode with their NT4 mikes had 12 dB pads built into the XLR5 connector. Does this cable have such pads in it? Or is it just straight wire from XLR to mini? I'm looking for one that doesn't have the resistive pads.

A: I bought this cable as a back-up for the one provided with my Audio-Technica stereo mic, and it's much less efficient, so I suspect that there is an unseen pad in the XLR, or the cable is simply more resistive. I'm returning it -- the signal into my Marantz digital recorder is too low.

Q: 9. Does this work with blx4r receivers ?

A: Yes, the Shure PS124 Power Supply With Non-Locking Power Connectors can be used to power four BLX4R receivers. I contacted Shure to confirm compatibility. This will work with multiple BLX4R receivers, If you need a replacement power supply for a single BLX4R, the Shure PS24US Power Supply for Select Wireless Receivers (B&H # SHPS24US) is the correct model. You may also want to consider using one master antenna for four BLX4R receivers with the Shure UA844+SWB/LC Wideband Antenna Distribution System & No Antenna Cables - 470 to 960 MHz (B&H # SHUA844SWBLP) which also includes a the daisy chain cable with four DC power feeds for the receivers.

Q: 10. Does this work with v-mount batteries? What's needed in terms of accessories?

A: The Waterbird MS SWIFT S 200 Camera Slider (79") has an XLR 4pin power input that can be used with a power supply. Waterbird Cube 24V Power Supply for MS SWIFT S/X & MS XL Systems BH #WAPSU24