This Marker Light Holder from Innovative Scuba Concepts clips onto your BCD or other dive gear and holds a light stick so your dive companions can see you. The holder has a swiveling snap hook and a nylon webbing strap.

Holds Light Stick    Swivel-Snap Hook    Nylon Web Strap

Related Questions and Answers

Q: 1. Any way for this to hold a sheet of Didymium glass that is 2-3mm thick?

A: No, will only support gels that are 1.42mm thick not glass that is 2.0mm.

Q: 2. Is there any type of counter weight made to help balance this?

A: Just buy some simple sand bags to hold the legs of the stand down. Simple sand bags are what the industry uses for this purpose.

Q: 3. The bottom collar on this lightstand has broken. I purchased a Porta Stand PS-3 collar to replace it but it's 1/8 too small in diameter for both the lower and upper leg sections. Are there any replacement parts available?

A: To obtain the replacement part you need, it would be best to contact Impact directly for assistance. The following link would be to their contact information: http://bit.ly/1g7INv4

Q: 4. Does this mask come with a strap?

A: Yes, it comes with a nice wide, comfortable, and easily adjustable strap.

Q: 5. If attaching a speedlite, will an accessory be necessary?

A: The end of the boom has a standard 5/8 light stand stud with a 1/4 screw. If you want to attach a speedlight, you will need to first attach something to the stud or 1/4 screw. The most common products for this is are a radio receiver, a cold shoe or a long off camera flash cable. Whichever you use, check to be sure it has a 1/4 tap for attaching to the 1/4' screw.

Q: 6. Can be used with a Blackmagic Video Assist 7" First version?

A: The CAMVATE Monitor Holder C-Frame Cage with 5/8" Light Stand Receiver (B&H# CAC2426) will not fit the Blackmagic Design Video Assist 7" 12G-SDI/HDMI HDR Recording Monitor (B&H# BLVIDA127HRD).

Q: 7. Can you take out the clip from the end and put it on the other end of the boom arm? I am trying to put a reflector so that the weight is equally balanced on both sides - specially when I do not need to extend it.

A: The Integral Reflector Clip on the Impact Multiboom Light Stand is able to slide up and down the length of the boom arm, but is not designed to be removed and attached to the opposite end of the boom arm. However, do note that there is a hole on the tail end of the boom onto which you may connect a counterbalance weight to offset any weight difference.

Q: 8. I just bought the Multiboom Light Stand and Reflector Holder, and it won't open. The legs at the base won't spread apart. I've fiddled with a lot of the knobs, but without further instructions I'm at a loss. Is there something I'm missing or did I get a defunct item?

A: There is a way but I can not describe, you need to play with it without applying much force. Change the connection point to central pole first then try legs.

Q: 9. What is the IMLSRH stand made of? Aluminum? Iron/Steel?

A: It's made of aluminum and you really need to use the weights in this link: a href= http://www.bhphotovideo.com/c/product/53583-REG/Tenba_636_206_Heavy_30_Sandbag.html target= _blank http://www.bhphotovideo.com/c/product/53583-REG/Tenba_636_206_Heavy_30_Sandbag.html/a

Q: 10. What size phones does it hold? Does it come with the ac adaptor? How thick of a surface can you clip to?

A: While not specified by the manufacturer, we were able to attach larger-screen phones to it, including my personal iPhone 13 Pro Max with a case on. It does not come with an AC wall adapter. The table clamp's jaw was easily openable to 2.2" but with effort could be made to open as wide as 2.55".