6 Channel Amplifier

Ashly Nxe Series Nxe4004 4-channel 400w Power Amplifier With Programmable Outputs & Ethernet Control

Product Code: ga13963
Availability: In Stock

$8,787.00 $10,808.01

Qty

0 reviews Write a review

Description
Reviews (0)

The nXe Series NXE4004 4-Channel 400W Power Amplifier with Programmable Outputs & Ethernet Control from Ashly is a Class-D switching amplifier combined with a switch mode power supply. This amplifier meets the requirements of demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers.

The rear panel has DIP switches for programming each channel output for either High-Z or Low-Z operation. This amplifier can be connected to a network with Ethernet control and features serial data control, aux preamp outputs, instant standby mode, preset recall, fault condition logic outputs, and optional network audio and digital audio capability, all controlled using the Protea Software Suite (not included).

General
Voltage Gain	Selectable at 26, 32, or 38 dB, and 1.4 V
Damping Factor	>250 (8 Ω load <1 kHz)
Filter	Input High Pass Filter: 80 Hz 2nd order
Distortion	<0.5% SMPTE, typical <0.5% THD-N, typical (8 Ω, 10 dB below rated power, 20 Hz to 20 kHz)
Channel Separation	-75 dB (dB from full output, 1 kHz)
Signal / Noise	20 Hz to 20 kHz, un-weighted >105 dB
Frequency Response	20 Hz to 20 kHz, ±0.05 dB
Connector	Balanced Input Connector: Euroblock 3.5 mm, 1/4" TRS and XLR combo jack
Input Impedance	10 kΩ
Maximum Input Level	21 dBu
Speaker Output	Connector: Neutrik & speakON
Network	Control Network: Compatible with standard 100 MB Ethernet
AUX Outputs	Connector: Balanced Euroblock 3.5 mm Maximum Output Level: 21 dBu
Contact Closure	Remote Standby: Euroblock 3.5 mm, close contact to GND for standby mode Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall
Data	Data Connection: Euroblock 3.5 mm - Gnd, 18 V, in, out
Outputs	Fault Condition Logic Outputs: 4 x 3.5 mm Euroblock
Level Control	Remote DC: 4 x 3.5 mm Euroblock - Gnd, CV, V+ per input
Attenuation	Front panel, software, offset link group, and remote per channel Fully off = mute
Protection Circuits	Inrush current limitation, temperature monitoring, output over-power protection, and mains fuses
Cooling	Continuously variable temperature controlled axial fans
Environmental	Non-condensing 32 to 113°F (0 to 45°C)
Power Requirements
Power	At 50 Hz Nominal (Automatic Sensing SMPS): 120 VAC Operating Range: 70 to 135 VAC Minimum Power-Up: 85 VAC At 60 Hz Nominal (Automatic Sensing SMPS): 240 VAC Operating Range: 140 to 270 VAC Minimum Power-Up: 170 VAC
Connector	Power Cable Connector: 20 A powerCON
Maximum Output Power	Per Channel, Low-Z Output, All Channels Driven 2/4/8 Ω: 400 W
Output	Low Z Output, Bridge Mode, All Channels Driven: 800 W (4/8 Ω) 70V, 100V Output, All Channels Driven: 400 W (70/100 V (per channel)
Power Draw	Sleep Mode: < 1 W Standby Mode: 40 W Idle (No Signal): 70 W
Current Draw	For 120 VAC Sleep Mode: 0.1 A Standby Mode: 0.70 A Idle (No Signal): 1.30 A For 240 VAC Sleep Mode: 0.05 A Standby Mode: 0.35 A Idle (No Signal): 0.65 A Maximum, All Channels Driven, Typical Input 1/8 Max Power @ 2 Ω): 5 A for 120 VAC, 2.5 A for 240 VAC
Dissipation	Thermal Dissipation: Sleep Mode: <3.4 BTU/hr Standby Mode: 136 BTU/hr Idle (no signal): 238 BTU/hr Typical (1 / 8 Max Power @ 2 Ω): 595 BTU/hr
LED Indicators	Front Panel LED Indicators White: Power Switch: On, off, standby (flashing) Red LED: Clip / Mute Per Channel: Clip @ 1 dB below full output / mute Protect: On (fault condition or shut down), Off Green LED: Signal Per Channel: -18 dBu, below rated output Bridge Per Channel Pair: On, off Com: On, for Ethernet data or device ID Current Per Channel: Proportional to output Yellow LED: Temperature Per Channel: On dim at 90% maximum operating temperature, full bright + protect at 100% Sleep: On, amplifier is asleep from audio inactivity Disable: On, power switch & front panel attenuators are disabled
Dimensions	19.0 x 3.5 x 16.8" (48.3 x 8.9 x 42.8 cm)
Weight	32.4 lb (14.8 kg)
Packaging Info
Package Weight	32.5 lb

4-Channel high-output amplifier with programmable output on each channel (High-Z or Low-Z, selected via rear panel DIP switches)

Power-saving, Energy Management System with automatic <1W sleep-mode (defeatable)

Front panel power switch and level controls (can be disabled for security)

Rear panel DIP switches per channel for selection of high pass filter, limiter, input gain, and High-Z or Low-Z speaker output configuration

Remote DC level control on each input channel

Switch mode power supply automatically detects 120 or 240VAC operation

Extensive protection circuitry and continuously variable cooling fans

Multiple independent internal power supplies provide increased channel separation and reliability

Ethernet port for control and monitoring of amplifier functions, with front panel COM activity LED

Serial data port for use with Ashly remote control devices, or optional RS-232 converter for third party controllers (not included)

Protea software allows to remotely disable all front panel controls, including the on/ off switch, for a tamper-proof installation

Real-time clock with event scheduler

Instant standby mode that can be triggered by contact closure, software control, or event scheduler for reduced power consumption

Programmable power-on delay

Preset recall via contact closure, software control, remote control, or event scheduler

Aux preamp outputs, and fault condition logic outputs

Optional Cobranet or Dante network audio and AES3 digital audio input with pass-through

Neutrik Combo XLR - 1/4" TRS jack plus Euroblock input connectors

Neutrik speakON twist locking loudspeaker connectors for security, safety, and reliability

Neutrik powerCON detachable AC mains connector

Made in USA

Related Questions and Answers

Q: 1. Is this rack mountable?

A: The AudioSource AD1002 does not offer any rack mounting hardware, however can be rack mounted using a universal rack shelf such as the Raxxess UNS-1 1U shelf. https://bhpho.to/2hfRR7V

Q: 2. Does the FA 125.2 have tone controls?

A: The Ashly FA-125.2 2-Channel Installation Amplifier does not feature EQ or tone controls.

Q: 3. How do you bridge the inputs so all 4 play the same sound ?

A: Bridge mode can be activated via a selector button on the back panel of the unit.

Q: 4. Can this be used just as a center speaker?

A: The Bowers & Wilkins Panorama 3 400W 3.1.2-Channel Soundbar cannot be used as only a center-channel speaker, as it is made to take full audio from the audio output of the TV.

Q: 5. If your amplifier is CE certified can I get testimony from you to that effect?

A: You can find Ashly's certifications by following the link below, and clicking on the 'features' tab. https://ashly.com/tra-convection-cooled/

Q: 6. What type of effects come with the amplifier

A: The Peavey PVi 8500 400W 8-Channel Mixer/Amplifier with FX and Bluetooth list of effects includes 3 different reverbs, Delay, Vocal Enhance, and Chrous.

Q: 7. Can two amps be joined together to fit in a 1RU rack space with the included hardware?

A: Yes, two of the QSC SPA2-60 2-Channel Power Amplifier (60W) can be mounted side by side in one rack space. Installation instructions for this configuration can be found in the installation guide here: https://bhpho.to/4aKF5J4

Q: 8. Is this amplifier CE certified?

A: The Ashly TRA-4150 is Not only CE certified but Safety/Compliance: TUV, FCC, and RoHS.

Q: 9. How to work the effects?

A: The available effects are dialed in via labeled EFX orange-colored knobs located on the front panel under the red MON knobs. Please follow the link provided below for the instruction manual and full operating details:http://bit.ly/1K9VVT9

Q: 10. This unit says it has 8-channel AES inputs. Does it also have 8-channel AES outputs?

A: AES3 digital audio output is available as a 4- or 8-channel option for the Ashly ne8800A Network Enabled Digital Signal Processor. The AES3 outputs are pass-through only (no DSP).

There are no reviews for this product.