Neutrik's 3-Pole XLR Female to BNC Female Adapter is a pre-wired connection point allowing you to conjoin heretofore incompatible items. In this case, you're given a rugged, die-cast shell which facilitates XLR female to BNC female connections.

Die-Cast Shell    Connection Between XLR Female and BNC Female

Related Questions and Answers

Q: 1. How long is the extension?

A: This product is 2.9 inches long.

Q: 2. How is this adaptor wired? We assume BNC "hot" goes to XLR pin 2, but is XLR pin 3 floating or strapped to XLR pin 1? Can we alter the internal wiring?

A: According to Neutrik, the NA2FBNC is wired so that XLR pin 2 is hot and pins 1 and 3 are wired to ground. The internal wiring on the adapter is not intended to be reconfigured. For more information about the wiring, please contact Neutrik directly. Their US office is located in Charlotte, NC and you can reach them by phone at 704-972-3050.

Q: 3. Does this product come in black?

A: No, Neutrik does not offer this adapter in black finish.

Q: 4. Can I use this to extend a SDI cable run?

A: The Pearstone BNC Female to BNC Male Right-Angle Adapter (B&H# PEABNCB1R) will connect to one female-end BNC and one male-end BNC. As such, if you somehow have an SDI cable with a female end (extremely rare) then you could theoretically use this for that purpose if the other end of that same cable is male. However, in all likelihood (you'll want to check), both of the ends of your cable are male. For that reason, you'll need a double-female connector to connect two cables that have male BNC plugs. Here's a good option for up to 6G-SDI: Pearstone BNC Female to BNC Female Adapter (B&H# PEABNCD1) https://bhpho.to/3PCtlyB

Q: 5. I need to bring XLR audio directly into the Aja IO 4k (https://a href= http://www.bhphotovideo.com/c/product/1025891-REG/aja_io_4k_10_bit_4k_uhd_sd_i_o_tb_2.html target= _blank www.bhphotovideo.com/c/product/1025891-REG/aja_io_4k_10_bit_4k_uhd_sd_i_o_tb_2.html/a). Will this do the trick?I'm thinking I connect my condenser mic to a mixer where it gets phantom power, output with XLR cable to this adapter and plug this adapter directly into one of the SDI BNC connections on the IO 4k. Will that work? Thanks!

A: Sorry, but the AJA Io 4K I/O for Thunderbolt 2 B&H # AJIO4K has no analog audio input connectors, only analog outputs. In order that we may better assist you, please write us with further detail about what you want to do. provideo@bhphoto.com.

Q: 6. Will this click in to a Zoom F3? My shotgun mic won't click in and I have seen others click.

A: Yes, the Neutrik 3-Pole XLR Female to 3-Pole XLR Male Extension Adapter will be compatible with the Zoom F3's locking Neutrik XLR connectors.

Q: 7. Does any other company make such an extender in black?

A: Unfortunately, we do not currently offer an option that is a 3-Pole XLR female to 3-Pole XLR male extension adapter in black.

Q: 8. Is this the best option for connecting one xlr cable to another, thus extending the length?

A: Yes, the Neutrik 3-Pole XLR Female to 3-Pole XLR Male Extension Adapter is a solid option to connect between 3-pin XLR male and 3-pin XLR female connection points.

Q: 9. Will this handle 300 watt crown amp to xlr in to bose 802?

A: The Neutrik NA4FX-F speakON NL4FX to 3-Pole XLR Female Adapter can be used to convert a male XLR output connector to a speakON connector. If you need a similar adapter a male XLR connector, you can use the Neutrik NA4FX-M speakON NL4FX to 3-Pole XLR Male Adapter (B&H # NENA4FXM). These adapters can be used with Crown amplifiers as well as with the Bose Panaray 802 Series Loudspeakers.

Q: 10. What is the ohms on this connector?

A: I am afraid that the exact Ohm rating of this connector is not listed by Pearstone. However if you must have 75 Ohm we have a similar angled connector from Comprehensive that is specifically rated at 75 Ohm and does not cost that much more. B&H # COABMBFRA will work very well for you.