Grab the authentic K1 Ceramic Heating Block Kit from Creality to give yourself peace of mind when replacing the heating block of your K1 or K1 Max 3D printer. With its all-metal construction, the heating block can withstand temperatures up to 300°C for uniform heating and superior heat transfer. The increased hot melt section supports high-speed printing up to speeds up to 600 mm/s with compatibility for more filaments such as PLA, ABS, nylon, and more.

300°C High Temperature Resistance    All-Metal Construction    Large Hot Melt Section    High Flow Support for up to 600 mm/s

Related Questions and Answers

Q: 1. can you manually control the iris on this camera?

A: Unfortunately you cannot.

Q: 2. What's the diameter of the light?

A: this light is not in stock so i can not measure the light. this is what the website said 0.67 x 10.24 x 37.87" / 1.7 x 26 x 96.2 cm

Q: 3. What kind of Battery this camera uses and which one you recommend to buy together the camera?

A: This camera comes with a D-Tap cable which will will allow you to use a battery like the IndiPRO Tools Micro-Series V-Mount Li-Ion Battery (98Wh), BH #INVMP98S. https://bhpho.to/35yKFgp

Q: 4. Are the lenses a new model of iZugar MKX22?

A: Yes, this Z CAM K1 Pro Cinematic VR180 Camera is equipped with MKX22.

Q: 5. Are the lenses interchangeable?

A: The lenses are not interchangeable.

Q: 6. Is this limited to the VR180 Google format or can the footage be used to produce Oculus video also?

A: The Z CAM K1 Pro Cinematic VR180 Camera, BH # ZCK2501, is VR180 Format Certified by Google but it will also work within the OCULUS VR format .

Q: 7. Is this camera suitable for 24/7 Streaming?

A: I would think not. This type of applications might literally burn-up the sensor. Use Z CAM WonderLive for a less intensive streaming experience.Supported Features:Up to 4K output resolution equirectangular imageSave live stitched video filePreview live stitched videoFacebook 360 Live integratedWeibo Live integratedRTMP live streaming outputQuick User GuideOpen Z CAM Controller, select network mode to Direct, connect Z CAM S1 to PC directly through the Ethernet port.Connect power to Z CAM S1 and it will be turned on automatically.PC should be connected to Internet in order to perform RTMP live streaming.On Z CAM Controller, click the tab Tools and select Z CAM WonderLive, four IP addresses will be detected and shown.Select the below options accordingly:Stitch template Auto adaptation : Configuration file will be generated automatically.PTGui file : Browse to select your own PTGui file deemed fit.Encode Select resolution, bit rate and IDR interval according to network conditions.RTMP Facebook Live : Facebook 360 Live integrated, click to select.URL : Manual input URL to stream.Output Preview : Select this output option to enable live preview in equirectangular format.SDI : Blackmagic Design DeckLink Studio 4K card has been functionally tested and verified. Note that if SDI is selected, all other output options would then be prohibited.Stitched file : Save stitched video (with audio track) to a file.Source file : Save original video/audio streams to four respective files.Note that RTMP, Preview, Saving stitched video could work simultaneously depending on system performance. Press Live to start live streaming.

Q: 8. What is the average record time in minutes for a 64GB SD Card, what is the max SD card capacity that can be used?

A: I use 128GB cards (max supported). Record time expected is over 4 hours for 128GB but I've never run that long myself.

Q: 9. Can 3 of these be used live into a mixer and switched?

A: Unfortunately that is not possible. These cannot be put in to a live video switcher and mixed.

Q: 10. Does it store RAW data?

A: No RAW. Captures in MOV (H.264 Codec)