The ErgoReach EP14 Premium Aluminum Articulating Dual-Screen Mount from Rocstor holds two displays up to 32" and 17.6 lb each. Attach this mount to your desk using the grommet or clamp depending on your desk's needs. 75 x 75 and 100 x 100mm VESA mounting is compatible with a wide variety of screens. -30 to 90° of tilt, ±90° of swivel, and 180° of rotation gives you control over positioning to find better viewing angles and avoid glares. A durable aluminum and steel construction with integrated cable channels give your setup a sleek aesthetic at home or in the office.

Holds Two Displays up to 32"    17.6 lb Weight Capacity    -30 to 90° of Tilt    ±90° of Swivel    180° of Rotation    75 x 75 & 100 x 100mm VESA Compatibility    Aluminum & Steel Construction

Related Questions and Answers

Q: 1. I have a glass desk that fits the width requirements, but I'm curious whether or not anyone has mounted it on glass? Any issues?

A: I have it mounted on a small glass top desk, it comes with a small rubber pad wich you just stick on the bracket to tighten. So far it holds good! No complaints.

Q: 2. Does this record audio with video?

A: The battery life of the Teslong TD500 Articulating Lens Inspection Camera with 5" Screen has a battery that lasts 3-4hrs of video recording. The Teslong TD500 supports microSD recording of video to the included 32GB card. The 32GB card will be able to store much more than 3-4hrs of video recordings. You can also add another card for even more video recording. SanDisk 32GB Ultra UHS-I microSDHC Memory Card BH #SASDSQ432GB

Q: 3. I have two 27in monitors will are the arms long enough to have both side by side?

A: You should no have issues mounting two 27" monitors with this mount.

Q: 4. camera dimensions?

A: The dimensions of the Minolta MN40WP Waterproof Dual-Screen Digital Camera (Red) are 4.4 x 2.7 x 1.3 inches (11.2 x 6.9 x 3.3 cm), and the camera weighs 5.8 oz (164.4 oz).

Q: 5. How far will the arm extend from the mounting pole?

A: 16.3" / 41.3 cm

Q: 6. Can anyone tell me the outer diameter of the pole this mounts on and if if the height can be adjusted quickly (uses a clamp or other quick release, not screws)?

A: It looks like I missed this email, caught it when cleaning up my inbox. But if the info can be used for future buyers, I am happy to respond. The standing support is 1 1/4 Dia., and yes the bracket that supports the arms has a lever (as shown in the picture) that can easily be adjusted up or down. The question wasn't asked, but the standing support is 16 tall. Hope this helps!

Q: 7. Will the clamp fit through a 2.5 inch hole? My cubicle backs up to a wall, i'd have to insert the clamp into the extra cable hole in the desk.

A: It depends on the exact shape and depth of the hole. The mounting flange is just shy of 2.5 but is D shaped (to go along a wall). The flange may or may not fit into the hole as the longest distance from the corner of the D to the opposite rounded edge is closer to 3 . However the clamping depth/height may allow for the rounded portion to fit to the hole and allow you to bring the entire clamp forward so that the rear-flat part of the D can take up the diameter of the hole. If the hole is only 2.5 and the desk thickness is more than 1.5 you might not be able to fit the clamp.But if the desk is about 1.5 and the hole is a generous 2.5 you will probably be fine.

Q: 8. Will this fit Dell monitors with recessed mounting holes?

A: Yes it will a simple long as the spacing is the same. It does not come with screws to mount it to the monitor. Your monitor should have the screws on the back of it already.

Q: 9. apple?

A: I agree, I have a 24 Eizo, monitor and a 22 NEC monitor attached, handles the load perfectly!

Q: 10. I'm new to this kind of stuff but have 2 LED displays. Does it matter if I have LED or LCD displays for this mount to be compatible?

A: Makes no difference. the bracket does not discriminate. What does matter is whether your monitors have a 3 or 4 hole pattern for mounting, but these two hole patterns are typical to just about all monitors.