The CV348 Compact 3G-SDI POV Camera from Marshall Electronics is designed with professionals in mind, and it delivers crisp video to fit the individual needs of productions large and small. The camera is built around a next-generation Sony 1/2.8" 2.2MP CMOS sensor capable of recording images at up to 108060 in low-light situations with rich color accuracy via 3G-SDI output. Marshall's C/CS interchangeable lens system offers a variety of focal lengths for both prime and varifocal options (a lens is not included).

Adapting to different environments and their requirements is easy with the camera's highly customizable settings, which may be adjusted with an optional Marshall controller, Camera Control software, or another third-party system using VISCA over RS-485. It also supports genlock, 12V barrel power, and stereo audio on the included breakout cable.

Compact POV Camera    2.2MP 1/2.8" Sony CMOS Sensor    C/CS Lens Mount    Up to 1080p60 via 3G-SDI    VISCA over RS-485 Serial Control

The next-generation Sony sensors provide clear HD images with rich accurate 10-bit (4:2:2) color, even in low light (0.01 lux), and the ability to switch to night mode (0.005 lux) where IR wavelengths can be captured in complete darkness.

Related Questions and Answers

Q: 1. Can this control a Marshall PTZ camera over a WAN? Meaning, when the camera is at a remote IP with open ports?

A: We are only aware that it will control cameras on a LAN network.

Q: 2. Will this work with a PTZ V60CL-N Camera?

A: Yes, the Globalmediapro RC-V60CL-NDI-POE HD-SDI, HDMI, IP PTZ Video Camera can be driven via rs-232.

Q: 3. Will this work on Sony BRC X1000 , Panasonic 22X hdmi NDI

A: No, Sony and Panasonic IP controlled PTZ cameras require their respective branded controllers for complete compatibility and operation. Controllers such as: SORMIP10 for Sony PAAWRP60GJQ for Panasonic

Q: 4. Does this support HD-SDI runs of 250ft?

A: Yes it does. You will be able to run a 250 foot HD-SDI cable with this system.

Q: 5. How do you convert the controller for fiber use?

A: So you need to convert both the sdi signal and data signal to a fiber signal. I prefer using a Thor 1-Channel Mini HD-SDI Single-Mode Fiber Optic Extender Kit for each Marshall Camera, but that is just me. It mux’s both signals to one fiber and demux’s at the other end. Hope this helps. Good luck!

Q: 6. Does this camera come shipped with the lens? Also, whats the zoom capacity of this camera?

A: It does not. A lens is not included with this camera. The Marshall Electronics M12-Mount 2.8-12mm IR Varifocal Lens, B&H # MACV28123MP, is a great option for a zoom lens. https://bhpho.to/2JiXJNh

Q: 7. where can I find the firmware update for the VS-PTC-150 ?

A: Looking on the Marshall Electronics firmware page, the VS-PTC-150 does not have any firmware updates available. You may wish to contact them directly. Marshall Electronics Tech Support. (800) 800-6608 (ext. 1129)

Q: 8. Does this camera come with a power supply?

A: Yes, the Marshall Electronics CV504-WP All-Weather Full HD Micro POV Camera comes with a 12V power supply.

Q: 9. what is the lag in-between switches like ? considering using in an iMag environment

A: According to AJA, if a route exists in the KUMO and the incoming signal is connected to the KUMO input, the delay time between the incoming signal and the output signal is less than 5 ns.

Q: 10. What connectors are on this device? Is it a male 8-pin Mini DIN?

A: No. It is a RS-232 8-pin.