Great for stages and wall washing, the Eliminator Lighting Mega Bar RGBA EP is a compact, 42” linear bar fixture that offers the flexibility of RGBA (red, green, blue, and amber) color mixing for your club, bar, or mobile DJ setup. The fixture has a total of 320 LEDs, with 64 red, 96 green, 96 blue, and 64 amber diodes. The fixture can be used in stand alone mode or connected in a primary/secondary configuration.

There are six operating modes, including Sound Active mode, Auto mode, RGB mode, Static Color mode, and DMX control mode (4, 6, 7, 9, 10, 18, and 34 channels). Use the 48 built-in color macros for quick and easy programming. The enclosure includes mounting brackets which double as a floor stand. The rear panel includes the LCD menu, 3-pin DMX, and power I/O for connecting up to 20 units, while magnetic end caps ensure the precise alignment of multiple bars. The Mega Bar RGBA EP is compatible with the ADJ RFC wireless remote control (sold separately). A power cord is included.

For Uplighting and Wall Washes    320 RGBA LEDs (Red, Green, Blue, Amber)    0 to 100% Electronic Dimming    30° Beam Angle    DMX Channels: 4, 6, 7, 9, 10, 18, 34    Variable Color Mixing    48 Built-In Color Macros    Gear Bag    Two Premium DMX Cables    RFC Wireless Remote Control

• 42" indoor linear fixture with 320, 10mm RGBA LEDs (64 red, 96 green, 96 blue, and 64 amber)
• 7 DMX channel modes: 4, 6, 7, 9, 10, 18, or 34 channels
• 6 operational modes: Manual Color, Static Color Change, Auto (Program Run), Sound Active, RGBA Manual control, and DMX512 
• Variable RGBA color mixing offers a seemingly unlimited color palette. Great for stage or wall washing
• 48 built-in color macros
• LED pulse and strobe effect
• DMX512 protocol
• Wired digital communication network
• Flicker free
• Refresh rate: 410 Hz
• Electronic dimming: 0 to 100%
• Beam angle: 30°
• Linkable via 3-pin XLR cable
• 4-button LED display on rear panel
• IEC AC outlet on rear to daisy-chain power (up to 20 units)
• Compatible with ADJ RFC wireless remote control (sold separately)
• Includes mounting brackets to mount on a wall or set on the ground
• Magnet system on endcaps to connect multiple bars together
• Low power consumption
• Very low heat output
• Runs all night—no duty cycle

Related Questions and Answers

Q: 1. How many bar you’ll get

A: There are 3 bars that are 4.5 ft long each.

Q: 2. how many rolls of paper come with this 3 pack ?

A: The Savage Background Leader Bar (3-Pack, 8.9' Long) listed above does not include a roll of seamless paper with its purchase; seamless paper would have to be purchased as a separate accessory.

Q: 3. can i use this for shure SCM 262 mixer?

A: Yes you can.

Q: 4. Can the end pieces be removed to use slightly wider paper?

A: While the end pieces cannot be removed, there is a longer version of this product with the Savage Background Leader Bar (8.9') B&H # SALB112. https://bhpho.to/2QuLcg4

Q: 5. Can I put the original Lusmandy bar on the top side and attach it to the mount while using this bar instead for accessories?

A: You could but you may need to drill additional holes in the OTA

Q: 6. Can this be cut down? I need 86” wide

A: Hi Aleksey! You can definitely cut down a 107" leader bar to 86" wide. We recommend using a fine tooth saw, and make sure to not cut where the clips are inside the leader bar.

Q: 7. I'm assuming these attach end to end to create a longer bar for longer rolls?

A: Yes. Correct the background leader bar will accommodate a 9ft roll of paper.

Q: 8. It says that each bar comes in 2 pieces, can I put 3 of these pieces together to get a custom length?

A: It is possible to use multiple Savage Background Leader Bars to accommodate a custom width.

Q: 9. Will these work on a v-flat to keep the edges from warping?

A: This is not compatible with a v Flat.

Q: 10. Where is this manufactured?

A: This product is manufactured in Laos.