Solidly constructed with aluminum and stainless steel, the 360° Houdini Speedrail to Rod Clamp from CineMilled provides both 1 1/2" and 5/8" rod clamps. This combination clamp can be used to build a customized mount for monitors, controls, or suction cups by connecting rigging rods of two different diameters. Endlessly customizable, this rigging component enables the very specific positioning of your gear to match the interior and external constraints of your production environment exactly.

Mounts Rigging Rod on Cheese Plate    1 x 1 1/2" and 1 x 5/8" Rod Clamp    For Suction Cups and Rigging Products    Clamps around Rigging Rod

Related Questions and Answers

Q: 1. So I want to fly my Sony fs700 on a Dji Ronin. Would this allow me enough wiggle room to operate efficiently or would I need additional parts?

A: You will be good with these two parts. If you were to add equipment to the back of the camera, say a battery, you would also need the CineMilled Pan Arm Extension for DJI Ronin Gen. 2 (Short) B&H # CICM502 or possibly the Long version. CineMilled Pan Arm Extension for DJI Ronin Gen. 2 (Long) B&H # CICM503 But if you are using just the FS700 and nothing on the back, the two extensions will be just fine.

Q: 2. Can someone suggest where to find a replacement for the large lever that tightens at the pivot point? I'm looking for a heavy duty one, preferably metal.

A: We do not have alternate levers for this mount. If the stock lever is having problems, or you have questions about it, please send an email to us at support@dracobroadcast.com. Also if there are any other technical or product related questions.

Q: 3. Do I need this bracket for Misfit, if I m using 15mm LW correct height?

A: The bare minimum, clip-on MisFit matte box requires the Bright Tangerine Lightweight Rod Bracket Type 4 for Misfit plus the Bright Tangerine 15mm Lightweight Rod Bracket Type 3 in order to be mounted on 15mm or 19mm rods.

Q: 4. About how long will the BP-945 power the BMPCC? Thanks.-Harold

A: Hello, the run time for the BMPCC with the BP-945 (assuming the camera uses 18 watts will be almost 2 hours. If you use the Ikan IBC988 with this same adapter - you can get more than 3.5 hours on a single charge.

Q: 5. Will this work with the C100 mark 2 if you have the extension arms or is the viewfinder still an issue?

A: You cant mount it without them and balance the setup correctly. I have successfully used them with the C100. Yes the eyepiece hits the frame when you tilt back more than I dont know,30deg. But all you do is tilt the Ronin backwards and you are fine. To balance the tilt axis instead of the handle being straight up during the procedure, take it off the stand and rotate the handle backwards 90deg and then proceed to balance.

Q: 6. I need to scan several rolls of 35mm microfilm. I know this product has 35mm and 120mm film holders does B&H have those and other accessories for CineStill Film Valoi 360 Film Advancer?

A: We do offer the CineStill Film VALOI 360 120 Film Holder, BH #CIV120HOLDER and the CineStill Film VALOI 360 35mm Film Holder, BH #CIV35HOLDER here: https://bhpho.to/34cJGXj

Q: 7. Will this fit the 3 legged thing tripod?

A: Yes this ArcaSmart dual plate will work with 3 Legged Thing tripods.

Q: 8. Can we hook it u to a RS3 Pro gimbal? How?

A: Yes, you can connect the CineMilled NODO 2-Axis Inertia Wheels Kit to the DJI RS3 Pro Gimbal. Just add the DJI Focus wheel BH #DJCPRN000801 to add an S-BUS port to your gimbal so you can connect the NODO.

Q: 9. Does this for a 30mm handlebar?

A: This is for a 25mm handlebar

Q: 10. Will this work with IFootage's Shark Slider?

A: Yes, the iFootage SA-32 Telescoping Support Rod can support iFootage Shark Sliders.