Connect rods, pipes, and surfaces with this Magic Arm with Dual Crab-Shaped Clamps from SmallRig. This mount features a crab clamp on each end of a magic arm with dual ball heads. The durable aluminum and stainless steel clamp assembly can support an accessory or gear weighing up to 7.7 lb using its multiple 1/4"-20, 3/8"-16, and 3/8"-16 anti-twist threads.

The magic arm features ball heads on either side that tilt and pan 360°, and there are 1/4"-20 screws on each end to mount the clamps. Each clamp can fit around a surface, rod, pipe, stand, or stick with a thickness or diameter of 0.6 to 2.6", and it secures using a large thumb lever. The inside of each clamp is lined with silicone for a solid grip.

Dual Ball Head Magic Arm    2 x Crab-Style Clamp Mounts    Clamps Mount on Surface 0.6 to 2.6" Wide    1/4"-20 & 3/8"-16 Anti-Twist Threads    7.7 lb Load Capacity, Rubber Padding    Large Thumb-Lever Fastener    Aluminum & Stainless Steel Construction

Related Questions and Answers

Q: 1. Will this work with with Manfrotto 208HEX Head Mounting Plate with Hex Stud - 3/8" Thread (BH #MA208HEX) ?

A: No, the Kupo 5/8 - Swivel Super Grip Double Baby Receiver with Ratcheted Handle will not accept the Manfrotto 208HEX Mounting Plate. That plate is only for grip hardware that has a hexagonal slot like a Manfrotto 035 Super Clamp without Stud, BH# MA035. https://bhpho.to/3dApUtZ

Q: 2. Does this work with Manfrotto super clamps?

A: The Impact ME-122P Single Background Holder Hooks for Super Clamps (2-Pack) BH #IMME122P can be used with Manfrotto Superclamps.

Q: 3. I have a Sirui K20X ballhead, how could I attach to this clamp?

A: As long as your ballhead is equipped with 5/8 or 1/4 threaded insert at the bottom, is just a matter of thread in baby stud into it and than secure ballhead into a clamp with provided wing screw. After that ready to use

Q: 4. Can the clamps be set parallel? Or is the joining stud itself offset?

A: No. The clamps can not be turned. They are permanently attached and fixed in the orientation you see in the product photo.

Q: 5. Does this fit the Blackmagic 6K Tilta cage?

A: yes this will fit the Blackmagic pocket in a tilta cage

Q: 6. Can I mount this onto the plate that comes with my Manfrotto 502AH video fulid head?

A: Yes, the bottom of the SmallRig Tripod Mounting Kit with 2 x Plates and 2 x 15mm Rod Clamps has threads in it's base which allow the base plate to mount to tripod camera plates, such as the plate found on top of the Manfrotto 502AH.

Q: 7. Hi, do the letters RL mean that the clamp has a ratchet handle?

A: Manfrotto has 4 versions of the Super Clamp with the Ratchet handle. The only differences are if the stud is included or not, & what particular stud. This 035RL Super Clamp includes a Standard Stud.

Q: 8. Whats the benefit or T handle compared to ratchet handle?

A: The Impact Super Clamp with Ratchet Handle BH #IMCC106R can be tightened down with more force and also in positions where the Impact Super Clamp with 5/8" Snap-In Pin BH #IMCC106TSIP could not be twisted with adequate force.

Q: 9. Does it mount onto Impact Light Stand, Black (6') B&H # IMLS6B MFR # LS-6B?

A: This clamp can attach to an Impact 6' Light stand either using the 5/8 female slot with the included stud removed on the clamp or it can bit the tubing of the stand in a horizontal position.

Q: 10. Can you use the standard Sony neck strap with the The L-Shaped Wooden Grip for Select Sony Cameras?

A: You would not be able to use a standard Sony neck strap with the SmallRig L-Shaped Wooden Grip for Select Sony Cameras, because the eyelet on one side of the camera is covered by the grip.