Power your speakers with the Behringer NX3000, a 2 RU, two-channel, 3000W amplifier with built-in SmartSense impedance compensation technology that delivers a linear response at any speaker load impedance. The amplifier also features a zero-attack limiter that provides maximum output level with exceptionally reliable overload protection.

The NX3000 delivers 2 x 1500W into 2 ohms or 3000W into 4 ohms bridged, giving you flexibility when deploying your sound system. Inputs are available via two combo XLR-1/4" inputs, while the speaker outputs utilize NL4 speakON speaker connectors. A power cord is included.

Two-Channel Amplifier: 2 x 1500W    2, 4, and 8 Ohms    Class-D Amplifier    SmartSense Impedance Compensation    All Controls Available from Front Panel    Two Combo XLR-1/4" Inputs    Two NL4 speakON Outputs    Includes Power Cord

• Ultimate reliability through revolutionary cool-running High-Density Class-D technology with near-zero thermal buildup
• Ultra-efficient switch-mode power supply for noise-free audio, superior transient response, and low power consumption
• Built-in stereo crossover with low-cut, high-cut, and full-range mode
• SmartSense loudspeaker impedance compensation features fully linear frequency response at any speaker load impedance
• Zero-attack limiters offer maximum output level with reliable overload protection
• Detented and illuminated gain controls for precise level setting
• Precise 4-segment Signal and Limit LEDs to monitor performance
• XLR and 1/4'' TRS combination input connectors for compatibility with any source
• Professional twist-lock speaker connectors for ultimate reliability
• Independent DC, LF, and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
• Back-to-front ventilation system prevents thermal buildup for reliable operation

• After pressing the Power button, the Power LED lights to show the amp is ready for action. All channels feature positive-detent gain controls with LEDs that light when a signal is present, as well as limit LEDs to indicate when the amplifier is running at full capacity.
• The rear panel is home to the combo XLR and 1/4" TRS Input connectors, making the NX3000 compatible with virtually any source, balanced or unbalanced. Professional twist-lock speaker sockets are provided to ensure every drop of output power gets to your loudspeakers.
• The rear panel is where you'll find the switches that enable the NX3000 amp to run in your choice of dual mono, stereo, or mono bridge modes. The NX3000's built-in Crossover switch sets the amp to Full-Range mode, where the output is sent unfiltered to your loudspeakers, or bi-amp mode, which sends only the low-frequency content (<100 Hz) to passive subwoofers, while the high-frequency content (>100 Hz) is channeled to your full-range loudspeakers.

Behringer's latest SmartSense Technology puts the punch back into Class-D amplification, providing a vastly improved full-range frequency response with powerfully dynamic bass and smoother high-frequency reproduction. The resulting output is no longer dependent on the actual load, but is rendered perfectly ruler flat via impedance compensation. NX3000's design also incorporates a significantly higher damping factor that yields better amplifier control over the loudspeaker, for stronger audio reproduction especially in the low frequencies.

Related Questions and Answers

Q: 1. does this unit have a cooling fan ?

A: This appears to use a heat sync with ventilation.

Q: 2. Will this work on a Sennheiser shotgun mic?

A: Yes but the Sennheiser KA-600 BH #SEKA600 tends to be more popular for that.

Q: 3. If a device supports sending phantom power out of its 3.5mm mic input, will this adapter/transformer pass the phantom power up the XLR cable to the mic?

A: We could not guarantee that 48v phantom power would pass properly through this type of adapter if being used with a balanced 3.5mm jack with phantom power output.

Q: 4. Would it be possible to hookup a subwoofer to this receiver? Thank you Bob

A: Yes, this unit has a stereo RCA subwoofer pre-out. You can connect 1 or 2 powered subwoofers.

Q: 5. where are the volume controls it looks bare of any knobs it said independant 8 channel?

A: The volume controls are located on the back. I use this unit as an amplifier for speakers throughout my house, each channel goes to a wall volume control knob first, then to speaker. I would highly recommend adjusting the channel control knobs on back of amp to limit the output to wall unit or the amp will burn them up. Go ahead and get 100 watt wall units if this is what you want to use it for. The amp is adjusted to about 60% output for each channel. I do have speakers also hooked up directly to amp as well (NO WALL CONTROL) , I just have the volume statically set for that zone, as for it would be very inconvenient to change the volume on the amp.

Q: 6. Is there a way to add phantom power device to use my audio Technica shotgun mic that I used to use with a DAT recorder that had phantom power, but now all my cables do not work with 1/8in cameras or devices. Thanks for any advice?

A: A device such as the Denecke PS-1A Portable Single Channel 48V Phantom Power Supply (BH #DEPS1A) could be used in between a phantom-powered shotgun microphone and the Kopul LMT100 Low to High Impedance Matching Transformer for proper connection to 3.5mm camera inputs: https://bhpho.to/3rPrNa4

Q: 7. Can this play all 4 speaker channels at once?

A: Yes, you can run all four output channels at the same time.

Q: 8. What is the difference between this cable and the cheaper Kopul XRSM-015B? I plan on connecting NTG2 (battery-powered) to my DSLR or PC. https://www.bhphotovideo.com/c/product/1221867-REG/kopul_xrsm_015b_xrsm_3_pin_xlr_female.html/specs

A: The LM100 is an impedance matching cable, low to high, while the other is not. If you are connecting to a line level input you will need the impedance matching cable, if you are connecting to a mic level input you will use the less expensive XLR to TRS cable.

Q: 9. will it connect to bluetooth headset?

A: Not directly, You would need a Bluetooth transmitter.

Q: 10. Can this be used with an equaliser?

A: Yes it can. It normal practice to use a graphic EQ for your monitors.