Protect your camera cables when tethering using this Arca-Type Quick Release Plate with Tether Cable Clamp from CAMVATE. This aluminum Arca-type plate mounts onto your camera using a 1/4"-20 center thumbscrew, via two 1/4"-20 screws, or using an Arca-type receiver. The top side features tethering grooves for your cables so they don't pull or accidentally disconnect.

Mounting Plate for Tethered Photography    Fits Arca-Type Receivers    Grooves in Base for Tether Cables    Prevents Cable Disconnection    1/4"-20 Screw and Threads    Durable Aluminum Construction

Related Questions and Answers

Q: 1. Will this work with a Leica IIIc?

A: This plate is designed for Leica M rangefinders. Depending on which Leica Mirrorless camera you have there are alternatives to this. I would suggest calling or chatting with our agents to better assist you.

Q: 2. Is this suitable for use with a Nikon 200-500 5.6 lens attached to a Nikon D500 and Black Rapid strap?

A: It looks too short to hold 200-500/5.6. I'm using Wimberley P20 with 200-500/5.6 and it's working great.

Q: 3. Would this plate fit in the Tilta Tiltaing 15mm LWS Baseplate Type V??

A: Yes, the SmallRig Quick Release Arca-Type Base and Plate will fit on the Tilta Tiltaing 15mm LWS Baseplate Type V.

Q: 4. Can I use that flip up element as a loop to hang my camera on a strap when it is off my monopod ???

A: If you're referring to the small loop that allows you to hand-tighten the plate to the camera...I wouldn't advise it. The screw is a direct connection to the camera and will most likely loosen as the camera swings on it. If you look at a mount designed for this, like the Peak Design PROdrive, you'll notice that it's got a rubber ring and what looks to be a split washer - minimizing possible twist and unscrewing. I'm sure there are other models that separate the connection point from the screw entirely so that full 360 degree spinning is possible without the screw loosening. The point is, those attachments are designer for leash carrying at the mount. This quick release plate is not. So while it might be possible to attach a strap to it - you'd risk it unscrewing through use and dropping your camera.

Q: 5. Will this work with a leica M6?

A: Our Leica Plate #2148 will fit the M series body including the M6.

Q: 6. is there a way to replace the 3/8 on the qr plate w another 1/4-20 s theres two 1/4-20 screws on the qr plate? i kno most cages are one 1/4 and. one 3/8 but the sony fx3 full cage from smallrig has two 1/4-20s on the bottom and i cant figure out how to mount it via arca swiss without sliding the cage sideways on to the baseplate, but the screws up the alignment of the lens support and of the blocks access to the battery door/makes it so i cant use a dummy battery

A: Yes, you can replace the 3/8"-16 screw with another 1/4"-20 screw on this quick release plate.

Q: 7. How heavy is this?

A: This item weighs 4oz.

Q: 8. Will this work on a canon 80D without obstructing ports?

A: Yes, CAMVATE Arca-Type Quick Release L-Plate is design for small and medium size DSLR cameras. Canon 80D DSLR fall in the medium size category.

Q: 9. Will this work on the M10?

A: No, the Acratech Arca-Type Quick Release Plate for Leica M is not compatible on the M10. Achratech says this will fit the M10, https://bhpho.to/3lO59ig .

Q: 10. can i use this product on a Vanguard SBH-100?

A: They had a shipment from Pro Media where the insert was fitted with Loc Tite so you could not remove it, beware