The Da-Lite 70379 Da-Snap Fixed Frame Screen can be mounted on the wall or in a wall opening. It has a viewing area of 100 x 160" for an aspect ratio of 16:10 and 189" diagonal.

Dual Vision is a flexible vinyl surface ideal for rear projection, but capable of both front and rear projection. It has a gain of 0.9 and 130° viewing angle. It is suitable for video projection under controlled ambient light conditions. With a wide viewing cone and light gray tint, a sharp image with no color shift is observed regardless of location in the room. This seamless surface can be cleaned with mild soap and water, and is flame-retardant and mildew-resistant. This surface has also achieved GREENGUARD GOLD Certification.

Reinforced black binding on all four sides attaches the surface to the frame with metal snaps. The snaps and binding are concealed by the frame, made of 1.5" square, matte black, powder-coated aluminum. The frame is slip-jointed at corners and joints. Standard wall-mounting brackets are included.

189" Diagonal    16:10 Wide Format    Dual Vision Front & Rear Surface    0.9 Gain / 130° Viewing Angle    1.5" Square Aluminum Frame

Related Questions and Answers

Q: 1. will this work with 3rd party filament

A: No it has an RFID chip with metering. There have been some hacks but the company keeps up on hack fixes.

Q: 2. What range of wavelengths of light LESS THAN 400 nm does this lens transmit at least 50% of? At least 25% of?

A: Unfortunately, the manufacturer does not rate the lens for IR absorptance. However, as there is no IR coating, such near IR in particular should be expected to pass with little attenuation.

Q: 3. how much 3D print befor the cartridge runs out of ink? (assuming full yellow color of 3d print)

A: Unfortunately there is no way to predict how long it will last because there are too many variables such as object size and the amount of yellow your object needs.

Q: 4. What size filament

A: The XYZprinting da Vinci Junior 1.0 3D Printer uses 1.75mm filament.

Q: 5. Will the Video 18 Fluid Head work with this tripod?

A: Yes, The Sachtler CF-100ENG 2CF Carbon Fiber 2-Stage Tripod Legs support the Video 18 heads 100mm bowl size and would work.

Q: 6. Can you replace the glass bed on the Jr 1.0? How?

A: Scott is correct

Q: 7. How much prints can I do with a single ink cartridge?

A: Unfortunately there are too many variables such as the size of the object and the amount of yellow ink you need.

Q: 8. How does this compare to the Sachtler flowtech 100 MS Carbon Fiber Tripod?

A: The Sachtler flowtech 100 MS Carbon Fiber Tripod with Mid-Level Spreader & Rubber Feet (BH #SA5585) has a payload limit of 66 lb, where as the Sachtler CF-100ENG 2CF Carbon Fiber 2-Stage Tripod Legs (100mm Bowl) - Supports 88 lbs can support up to 88 lb. The 100 MS also has a single leg lock point vs the 2 leg lock points of the CF-100ENG. The overall leg design is different as well.

Q: 9. Can this stay upright with just rubber feet, or do I also need to purchase a spreader?

A: You need a spreader. Also the rubber feet are not included. You need to buy them separately.

Q: 10. Whats the weight like? I'm currently using a Sachtler hotpod and was looking into a lighter weight tripod that I could travel with. How much weight difference is there with a hotpod versus this set of sticks with an 18s fluid head on it?

A: The Sachtler CF-100ENG 2CF Carbon Fiber 2-Stage Tripod Legs weighs in at 5.3 lb. The Sachtler HOT-POD 10 Carbon Fiber Hot-Pod Tripod with Pneumatic Column weight in at 12.8 lb (5.8 kg). The weight difference with the same head would be 7.5lbs/3.4kg.