Fly with precision control and the ability to receive essential telemetry with the 16IZS 18-Channel RC Transmitter for Airplanes from Futaba. Supporting the FASSTest and S.BUS2 systems, this transmitter offers bidirectional data transmission over the 2.4 GHz wireless spectrum, and it lets you utilize multiple servos, gyros, and telemetry sensors with minimum cabling required. The telemetry received can be read aloud with the voice telemetry feature or displayed on the HVGA 4:3 color backlit LCD touchscreen, which is transflective for both indoor and outdoor use. When flying, the airplane's throttle is ratcheting, while steering is fine and precise, thanks to a single ball bearing for each stick axis and a high-cycle potentiometer. Please note that a receiver is required and not included.

18 Channels with 16 Linear & 2 Switched    2.4 GHz Bidirectional FASSTest System    S.BUS2 Component System Support    Receiver Required & Not Included    HVGA 4:3 Color Backlit LCD Touchscreen    Use in PC Simulation via USB-C Port    Ratcheting Throttle Control    Voice Telemetry Can Read Data Aloud    Vibration Alerts for Low Voltage & More    Firmware Upgradable via microSD

You can fly real RC aircraft or use the transmitter like a joystick in simulation software on your Windows-based PC. Simply connect it to your PC with an optional cable connected to its USB-C port.

S-FHSS Protocol

• R2008GS
• R2008SB
• R2106SB
• R2001SB
• R2000SBM

T-FHSS Telemetry Protocol

• R3001SB
• R3004SB
• R3006SB
• R3008SB

T-FHSS Mono (Non-Telemetry)

• R3206SBM
• R3106GF

FASST7 and FASST Multi

• R6004FF
• R6008HS
• R6014HS
• R6016HF
• R616FFM
• R617FS
• R6202SBW
• R6203SB
• R6208SB
• R6303SB
• R6303SBE

FASSTest12 and FASSTest18

• R7003SB
• R7006SB
• R7008SB
• R7108SB
• R7014SB

• 18 channels (16 linear and 2 switched)
• Mount accessories onto the multi-holder with an optional M3 screw
• Use an optional microSD to store model data files and update firmware
• Vibration alerts for low voltage and other user-defined alarms
• Powerful processor allows for channel mixing to operate on a curve for precise settings and improved feel

Related Questions and Answers

Q: 1. Could the transmitter work as IFB transmitter with the mic input (meaning the mic in could be used in conjunction with inputs in the back)?

A: There is a line input on back ot transmitter which may be used: The stationary transmitter is equipped with three XLR-1/4" combo jacks, one 1/8" mic, and one 1/8" line input, so it can be used for both music and voice transmission

Q: 2. Will this trigger more than one flash unit or do two receivers need to be purchased?

A: A receiver for each flash/strobe needs to be purchased.

Q: 3. Since the 18T offers its own wifi, does it provide dhcp? That is, could it become the network hub for a portable production?

A: No, the Allen & Heath CQ-18T cannot be used as a network hub.

Q: 4. Does the on camera transmitter have an off switch or does it not consume battery when not in use?

A: No, the following unit does not offer a on/ off switch.

Q: 5. I have a set of Photogenic strobes (from the early '90's). Will this work with Photogenic strobe models from that time frame?

A: If your Photogenic strobes use the standard IEC power cable and has either a 1/8 (3.5mm) miniphone sync terminal or 1/4 headphone sync terminal, then yes, the Impact PowerTrigger 16 Channel AC Transmitter and Receiver Set would be compatible for use with your strobe units.

Q: 6. Will this work for sony a7III ?

A: No, Sony uses a multi interface system for the shoe and remote. Click the link below to view; https://bhpho.to/2ED0aLJ

Q: 7. I checked the compatibility section, only AVATA 2. But will it be compatible with Mavic 4Pto in the future?

A: The DJI RC Motion 3 is compatible with the DJI Avata 2, DJI Mini 4 Pro, DJI Air 3, and the DJI Goggles 3. We do not have any information about potential compatibility with other drones in the future.

Q: 8. Would this unit be suitable for bal audio distribution from mixer to powered speakers? (sound reinforcement without spkr or audio lines from mixer to powered cabs) thank you

A: This system worked well for in-ear monitors but we used this system and it worked a lot better than the vocopro system: https://a href= http://www.bhphotovideo.com/c/search?Ntt=Alto%20Stealth%20Wireless%20-%20Stereo%20Wireless%20System%20for%20Active%20Loudspeakers%20%20&N=0&InitialSearch=yes&sts=ma&Top+Nav-Search= target= _blank www.bhphotovideo.com/c/search?Ntt=Alto%20Stealth%20Wireless%20-%20Stereo%20Wireless%20System%20for%20Active%20Loudspeakers%20%20&N=0&InitialSearch=yes&sts=ma&Top+Nav-Search=/a

Q: 9. Can this connect to a digital stage box running cat5 instead of a snake?

A: No, the Allen & Heath CQ-18T will only adapt to a stage box that runs off a snake. the cat5 input is only for the ability to input and output digital signals in parallel to a computer. Please review which stage boxes we have avaliable. https://www.bhphotovideo.com/c/accessories/Stage-Boxes-for-the-Allen--Heath-CQ-18T/1782750-REG-49489

Q: 10. hi I just bought this trigger ( impact power trigger) and is not working... I have a canon 6d and have put the transmitter on the hot shoe of the camera and the red light has not light up even though i tried the 16 channels. the equipment is new so I may say the battery is new too... the connection in the impact vsd 160 monolight is ok... could it be a problem on the camera? I also have trouble shooting with the original sync cord that came with the monolight... please any indications will help. Thanks

A: I had the same difficulties with my trigger. I sent it back to the manufacturer and they said they could not find anything wrong with it. I did try I few things to troubleshoot it including the battery but it still didnt work. Impact said they would ask B&H to refund me.