This QCM41 4-Way Cross Piece for M222 Truss from Milos Structural Systems allows 4 sections of M222 truss to connect and extend from a central point.

Connects 4 Truss Sections

Related Questions and Answers

Q: 1. I have the ADJ Event Table II, will this work on the tubing which is 1.3mm diameter?

A: Unfortunately, this clamp only works on tubing up to 1" thick. The Global Truss JR CLAMP for F23 and F24 Truss Tubing (Black) works on a maximum tube diameter of 1.37". https://bhpho.to/2TeMgCY

Q: 2. How much weight can it handle?

A: The capacity of the corner is dependent on the horizontal and vertical span that it will be connected to. How are you using it and how wide and the tall if the truss that it is being connected to? How much weight do you need to load on the truss system?

Q: 3. What it the max hanging weight limit on this

A: The Milos QuickTruss ULTRA Display Square Truss Kit (13.0 x 13.0') technically, if the system was being used indoors, on level ground cable of supporting the loads being applied, then the system could support as much as 2,900 Lbs. per 4m side, for a combined load of 11,600 Lbs. on the total system. This is based on a uniformly distributed load across each of the 4m spans of truss (so things like cables, drapes, etc.). If a large point load is preferred then the user could apply a single point load of 2,500 Lbs. anywhere on each side (so 10,000 Lbs. total if that load was applied to each of the 4 sides). This also assumes that the loads can be applied in such a way as to not damage the members of the truss (suitable clamps, slings, etc.). Outside use there are way more variables and best is to contact the lighting department in chat.

Q: 4. No specs listed. What are the dimensions of this foam - length,width, height?

A: Dimensions are: 1st piece, 11.5" x 9" x 1" 2nd piece, 10.5" x 7.5" x 0.5" 3rd piece, 10.75" x 7.75" x 1" 4th Piece, 11.5" x 8.5" x 1"

Q: 5. What is the equipment weight capacity for this rail?

A: You're safe up to 5 pounds. Anything more than that you might want to check with Novoflex: mail@NOVOFLEX.com

Q: 6. Can more trust sections be added to make the structure larger?

A: One could add Milos QuickTruss Ultra 12" pieces to create alternate forms and structures using the pieces of the Milos QuickTruss ULTRA Display Square Truss Kit (16.4 x 16.4') (B&H# MIBOOTH5X5U). Whether or not your particular design will be safe and stable will depend on the decisions that you make regarding any modifications. Milos QuickTruss Ultra 12" pieces are compatible with the pieces of this kit.

Q: 7. What is the length of each section of truss? can the parts be reconfigured?

A: The manufacturer does not specify the lengths of each section. Truss can be configured in many ways, but this kit was designed around a specific purpose. Other configurations might require additional clamps, clips or other components.

Q: 8. Do I need to buy corners and connectors separately or are they included?

A: This is a full kit with the assembly materials.

Q: 9. Is the body sect. cut into 2CM squares? Picture doesn't show nor does it define 'pick 'n pluck'

A: The center section is Pick N Pluck.

Q: 10. Do you need any additional hardware to connect this to a f34 truss?

A: The Global Truss SQ-4121 2-Way 90° F34 Square Truss Corner (Silver) only comes with one set of connectors. If you do not have any you will need another set, four of, BH #GLCOUPLER (https://bhpho.to/47xtHjm)