This 24" Neewer Light Reflector with Stand is ideal for image-makers who find themselves in a variety of shooting situations. The reflector is built around a translucent base that can be used as a diffuser. A reversible sleeve gives you white, black, gold, and silver surfaces and prepares you for just about any situation. Also included is an aluminum light stand with a 21 to 43" height range and 11 lb load capacity. Besides these, a reflector clamp with a stand mount and a 1/4"-20 to 3/8"-16 screw adapter are supplied. The nylon reflector easily collapses to fit in its included bag.

5-in-1 Collapsible Reflector    White, Black, Gold, Silver, Translucent    Adjustable 43" Stand with Clamp    Nylon Material    Includes 1/4"-20 to 3/8"-16 Adapter    Includes Carry Bag

Related Questions and Answers

Q: 1. There sint any instructions, How do I make this stand go Horizontal ?

A: There is a small rounded knob just next to the ratchet handle which you would need to loosen first. Next, you would pull the arm which has the reflector clips on it straight up until you can see the end of the arm. Lastly, you need to tilt the arm to your left or right (depending on which orientation you are standing in) and lock down the same knob mentioned earlier.

Q: 2. Can I sync more than two Vision 4 lights together?

A: Yes. The following system will all communicate together.

Q: 3. Is it possible High Speed Sync funcin with this flash?

A: No. The following unit does not support TTL, HSS Mode; Extremely short flash duration: from 1/1000 to 1/10000 seconds.

Q: 4. Can I use a Canon 580 slave flash with the vision 4?

A: Neither the Canon 580EX Speedlite Flash nor the Canon 580EX II Speedlite Flash are compatible with the Neewer Vision4 Battery-Powered Strobe when the 580EX/580EX II are used off-camera as a slave flash. The 580EX/580EX II flashes do not have built-in optical slaves. If you are using the 580EX/580EX II on-camera as a optical trigger, then you may use the Neewer Vision4 Battery-Powered Strobe in optical slave mode so the 580EX/580EX II will wirelessly trigger the Neewer Vision4 Battery-Powered Strobe.

Q: 5. What is the IMLSRH stand made of? Aluminum? Iron/Steel?

A: It's made of aluminum and you really need to use the weights in this link: a href= http://www.bhphotovideo.com/c/product/53583-REG/Tenba_636_206_Heavy_30_Sandbag.html target= _blank http://www.bhphotovideo.com/c/product/53583-REG/Tenba_636_206_Heavy_30_Sandbag.html/a

Q: 6. I need a grid for this flash. What is the size of the reflector?

A: According to the manufacturer, the Neewer Vision 4 Studio Flash Strobe comes with a 7" reflector that accepts 7-inch grids. As such, the Impact 7" Grid (30°), B&H # IMG730, would be a good option if you are looking for a single filter, whereas the Impact 7" Grid Set (10/20/30/40°), B&H # IMG7SK, or the Studio Essentials 4-Honeycomb Grid Bundle for 7" Reflector, B&H # STMR7G101, would be good options if you need a complete grid set.

Q: 7. Can you take out the clip from the end and put it on the other end of the boom arm? I am trying to put a reflector so that the weight is equally balanced on both sides - specially when I do not need to extend it.

A: The Integral Reflector Clip on the Impact Multiboom Light Stand is able to slide up and down the length of the boom arm, but is not designed to be removed and attached to the opposite end of the boom arm. However, do note that there is a hole on the tail end of the boom onto which you may connect a counterbalance weight to offset any weight difference.

Q: 8. Is this compatible with the canon sl3 camera?

A: No, Canon SL3 offers no single pin on the hot shoe in order to trigger off the unit.

Q: 9. What is the angle of this reflector? Is is an Umbrella reflector ?

A: The reflector is the standard one that comes with that Indra 500 Phottix flash. It does not list a specific angle or degrees it spreads the light.It is a seven inch reflector, can be used with an umbrella and it can be used with 7 inch grids.

Q: 10. Is there any type of counter weight made to help balance this?

A: Just buy some simple sand bags to hold the legs of the stand down. Simple sand bags are what the industry uses for this purpose.