PolyMide PA6-CF from Polymaker is a carbon fiber reinforced PA6 (Nylon 6) filament. The carbon fiber reinforcement provides significantly enhanced stiffness, strength, and heat resistance with outstanding layer adhesion. PolyMide PA6-CF is from the PolyMide family of Nylon/polyamide based filaments and features Polymaker's Warp-Free technology, which allows the production of Nylon-based filaments that can be 3D printed with excellent dimensional stability and near-zero warpage. This is achieved by the fine control of microstructure and crystallization behavior of Nylon, which enables the material to fully release the internal stress before solidification.

PolyMide PA6-CF is compatible with most of the 3D printers available on the market. Examples include the Ultimaker, Flashforge, Snapmaker, LulzBot, Raise3D, Flsun, Artillery, Anycubic, Creality, and more.

Please check out the below print settings and other properties, which are based on the use of a 0.4mm nozzle and the Simplify 3D v.4.0 printer.

Carbon Fiber Reinforced PA6 (Nylon 6)    Enhanced Strength and Heat Resistance    Polymaker Warp-Free Technology    536 to 572°F Print Temperatures    30 to 60mm/s Print Speeds

536 to 572°F

30 to 60mm/s

77 to 122°F

Almost any surface with a thin coat of PVA glue or Magigoo PA

Off

Related Questions and Answers

Q: 1. Is center column removable?

A: Yes it is!

Q: 2. Is the center column removable and if so then how low it can go to the ground?

A: With the Slik Pro CF-733 Tripod (Black) one can remove the lower part of the center column to get lower to the ground. One can then get down to 8.3" (This does not include the height of any head one may use). Alternatively one can invert the center column to get even lower to the ground.

Q: 3. What is the length of the center column?

A: While the manufacturer does not list the total length of the center column, Slik USA does indicate that the maximum height when the center column is down is 48.8 inches, and the maximum height when the center column is fully extended is 64.2 inches. As such, the center column would have 15.4 inches (39.11 cm) of travel from the lowest to highest setting.

Q: 4. What is the diameter of the base plate (where the head attaches)? Would the manfrotto befree video head fit on this neatly, says it is best that it be a 40mm base plate?

A: The base plate is about 2" wide, and would fit the Manfrotto BeFree video head quite nicely on it.

Q: 5. What is the outside diameter of the top of the center column (where a head would be mounted)?

A: According to Slik USA, the platform plate on the top of the center column on the Slick CF-633 tripod is 1-5/8" in diameter.

Q: 6. What is the diameter of the upper CF legs?

A: Diameter of the first upper leg is; 25mm.

Q: 7. Is this case large enough to hold the Nikon D750 with a 24-120mm lens?

A: It holds my D810 wit a 24-70 perfect. I hope this helps!

Q: 8. Is the case deep enough to use with the hoods attached for the lenses recomended?

A: The case is wide enough to keep the hoods on in reverse. The case is not long enough to have the hood attached for shooting.

Q: 9. Will this case accommodate D810 with 24-70 Nikon VR lens?

A: The Nikon CF-DC4 Semi-Soft Case (Black) will not accommodate the D810 with the Nikon 24-70mm f/2.8 lens.

Q: 10. Is this made in Thailand or China?

A: This tripod is manufactured in Thailand.