PolyMide PA6-CF from Polymaker is a carbon fiber reinforced PA6 (Nylon 6) filament. The carbon fiber reinforcement provides significantly enhanced stiffness, strength, and heat resistance with outstanding layer adhesion. PolyMide PA6-CF is from the PolyMide family of Nylon/polyamide based filaments and features Polymaker's Warp-Free technology, which allows the production of Nylon-based filaments that can be 3D printed with excellent dimensional stability and near-zero warpage. This is achieved by the fine control of microstructure and crystallization behavior of Nylon, which enables the material to fully release the internal stress before solidification.

PolyMide PA6-CF is compatible with most of the 3D printers available on the market. Examples include the Ultimaker, Flashforge, Snapmaker, LulzBot, Raise3D, Flsun, Artillery, Anycubic, Creality, and more.

Please check out the below print settings and other properties, which are based on the use of a 0.4mm nozzle and the Simplify 3D v.4.0 printer.

Carbon Fiber Reinforced PA6 (Nylon 6)    Enhanced Strength and Heat Resistance    Polymaker Warp-Free Technology    536 to 572°F Print Temperatures    30 to 60mm/s Print Speeds

536 to 572°F

30 to 60mm/s

77 to 122°F

Almost any surface with a thin coat of PVA glue or Magigoo PA

Off

Related Questions and Answers

Q: 1. Is the case deep enough to use with the hoods attached for the lenses recomended?

A: The case is wide enough to keep the hoods on in reverse. The case is not long enough to have the hood attached for shooting.

Q: 2. What is the outside diameter of the top of the center column (where a head would be mounted)?

A: According to Slik USA, the platform plate on the top of the center column on the Slick CF-633 tripod is 1-5/8" in diameter.

Q: 3. What is the diameter of the base plate (where the tripod head attaches)? Will this fit nicely with the Manfrotto BeFree video head (it's base is 40mm)?

A: The base plate is about 2" wide, and would fit the Manfrotto BeFree video head quite nicely on it.

Q: 4. Will this case accommodate the D850 and any of the smaller lenses?

A: Yes, it will fit with plenty of room.

Q: 5. Hi, What is the leg tube diameter of the CF-834?

A: Slik Pro CF-834 Tripod is a 4 section leg tripod. Stating from the thinnest to the thickest section they increment as fallow: (19 ,22 , 25, 27mm)

Q: 6. Is the case meant to stay on the strap while shooting?

A: Yes, the case stays on the strap when you are shooting.

Q: 7. Will this case fit AF-S NIKKOR 58mm f/1.4G Lens on a D810 ?

A: It should fit fine. The case is meant to fit most small prime lenses. Once you get into longer focal lengths or zooms it won't fit.

Q: 8. What is the thread size?

A: This tripod has a reversible screw. One side is 1/4" the other side is 3/8".

Q: 9. "Center column is removable, which allows the tripod to be set at a minimum height of 4.9" How can it be used without the center column, unless there is a short one available to take its place?

A: The center column splits near the top, turning it into a short center column.

Q: 10. What is the length of the center column?

A: While the manufacturer does not list the total length of the center column, Slik USA does indicate that the maximum height when the center column is down is 48.8 inches, and the maximum height when the center column is fully extended is 64.2 inches. As such, the center column would have 15.4 inches (39.11 cm) of travel from the lowest to highest setting.