The black Dana Dolly Center Support with High Density Foam provides support for your track when using heavy cameras, or with long track runs. Featuring a load capacity of up to 70 pounds, the support utilizes a TVMP adapter so you can mount it on an optional stand with a 5/8" (baby) stud. Please note that Dana Dolly recommends using at least a Beefy Baby stand with the Center Support.

It is made from lightweight 6061 aluminum that has been powder coated for protection from corrosion and to lower reflections from lights that could affect your shot. Felt tabs sit atop the support to cushion your track and prevent metal-to-metal contact.

TVMP Mount    Fits on 5/8" (Baby) Stud    Powder Coated 6061 Aluminum    70-Pound Load Capacity    Felt Tabs

Related Questions and Answers

Q: 1. Can you stack more than two together to increase the height?

A: We are not aware of that being possible with this product.

Q: 2. Does this product only come with only one track end? or does it come with a pair?

A: The Dana Dolly Universal Track End Bracket (B&H# DADDUTE1) is a single track end bracket and not a pair.

Q: 3. 9' might be a little long for what I need. Is there a way to shorten it?

A: The track kit comes in sections, so use 1 section only.

Q: 4. Can I use this with the Sachtler Aktiv head adapter? I want to use it with my Aktiv8 head.

A: Dana Dolly makes an adapter for the Sachtler aktiv6, 8, 8T, and 10. Dana Dolly 75mm Adapter for Sachtler aktiv6, 8 & 8T https://www.bhphotovideo.com/c/product/1682567-REG/dana_dolly_ddaktiv75adp_75mm_adapter_for_sachtler.html Dana Dolly 100mm Adapter for Sachtler aktiv10 https://www.bhphotovideo.com/c/product/1682566-REG/dana_dolly_ddaktiv100adp_100mm_adapter_for_sachtler.html

Q: 5. will this work with the dana dolly 100mm bowl adapter?

A: Yes, The Dana Dolly 6" Mitchell Riser Plate works with all Dana Dolly Adapters, and it attaches with the supplied tie down and washer. No additional parts are needed. The adapters attach just as they would on the dolly.

Q: 6. Does this package come with two end brackets or just one?

A: Only one per order.

Q: 7. Can you mount this 'unslung' on the bottom side of the Dana dolly as is, or are there other bits you'd need?

A: Just as is

Q: 8. Says the track end does not work with C-stand studs? Is the hole too small or too large?

A: Generally C-stands come with a 5/8 (16 mm) male pin. The Dana Dolly Original Track End Bracket is supported by a Junior or 1 1/8 receiver. You may use an an adapter such as this item below for attachment of the Dana Dolly Original Track End Bracket.

Q: 9. What is the benefit of this over the standard tube track they offer?

A: The Dana Dolly track kit #DADDTRKKT1 offers track that bolts together, whereas the pipe kit screws together. The triangle track kit has a patented seam that is angled so that no wheel crosses the seam at the same time as any other wheel. The triangle is a little stronger; however, the kit weighs more because of the case. The triangle track kit weighs 54 pounds (24.49 kg) in the case, whereas the pipe kit in its bag weighs 25 pounds (11.34 kg). Dana Dolly Track Kit ( Triangle kit) BH #DADDTRKKT1 Dana Dolly Portable Aluminum Pipe Kit (6-Pack, 39") BH #DADDPPK1

Q: 10. What is the track width that these brackets provide?

A: The track width is 12 .